- 您現在的位置：買賣IC網 > PDF目錄358620 > 30046-23 (NATIONAL SEMICONDUCTOR CORP) Low Power Integrated x86-Compatible 32-Bit Geode GXLV Processor(低功耗集成兼容X86的32位 Geode GXLV技術處理器) PDF資料下載
參數資料
| 型號： | 30046-23 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Low Power Integrated x86-Compatible 32-Bit Geode GXLV Processor(低功耗集成兼容X86的32位 Geode GXLV技術處理器) |
| 中文描述： | 32-BIT, 200 MHz, MICROPROCESSOR, CPGA320 |
| 封裝： | SPGA-320 |
| 文件頁數： | 88/247頁 |
| 文件大?。?/td> | 4379K |
| 代理商： | 30046-23 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁
www.national.com
88
Revision 1.2
Processor Programming (
Continued
)
G
3.7.6
SMM memory space is defined by specifying the base
address and size of the SMM memory space in the SMAR
register. The base address must be a multiple of the SMM
memory space size. For example, a 32 KB SMM memory
space must be located at a 32 KB address boundary. The
memory space size can range from 4 KB to 32 MB. Execu-
tion of the interrupt begins at the base of the SMM memory
space.
SMM Memory Space
SMM memory space accesses are always cacheable,
which allows SMM routines to run faster.
3.7.7
The GXLV processor implements SMI generation for VGA
accesses. When enabled memory write operations in
regions A0000h to AFFFFh, B0000h to B7FFFh, and
B8000h to BFFFFh generate an SMI. Memory reads are
not trapped by the GXLV processor. When enabled, the
GXLV processor traps I/O addresses for VGA in the fol-
lowing regions: 3B0h to 3BFh, 3C0h to 3CFh, and 3D0h
to 3DFh. Memory-write trapping is performed during
instruction decode in the processor core. I/O read and
write trapping is implemented in the Internal Bus Interface
Unit of the GXLV processor.
SMI Generation for Virtual VGA
The SMI-generation hardware requires two additional
configuration registers to control and mask SMI interrupts
in the VGA memory space: VGACTL and VGAM. The
VGACTL register has a control bit for each address range
shown above. The VGAM register has 32 bits that can
selectively disable 2 KB regions within the VGA memory.
The VGAM applies only to the A0000h to AFFFFh region.
If this region is not enabled in VGA_CTL, then the con-
tents of VGAM is ignored. The purpose of VGAM is to pre-
vent an SMI from occurring when non-displayed VGA
memory is accessed. This is an enhancement which
improves performance for double-buffered applications.
The format of each register is shown in Table 4-37 on
page 163.
3.7.8
Upon entry into SMM, after the SMM header has been
saved, the CR0, EFLAGS, and DR7 registers are set to
their reset values. The Code Segment (CS) register is
loaded with the base, as defined by the SMAR register,
and a limit of 4 GB. The SMM service routine then begins
execution at the SMM base address in real mode.
SMM Service Routine Execution
The programmer must save, restore the value of any reg-
isters not saved in the header that may be changed by the
SMM service routine. For data accesses immediately after
entering the SMM service routine, the programmer must
use CS as a segment override. I/O port access is possible
during the routine but care must be taken to save registers
modified by the I/O instructions. Before using a segment
register, the register and the register
’
s descriptor cache con-
tents should be saved using the SVDC instruction.
Hardware interrupts, INTRs and NMIs, may be serviced
during an SMM service routine. If interrupts are to be ser-
viced while executing in the SMM memory space, the
SMM memory space must be within the address range of
0 to 1 MB to guarantee proper return to the SMM service
routine after handling the interrupt.
INTRs are automatically disabled when entering SMM
since the IF flag (EFLAGS register, bit 9) is set to its reset
value. Once in SMM, the INTR can be enabled by setting
the IF flag. An NMI event in SMM can be enabled by set-
ting NMI_EN high in the CCR3 register (Index C3h[1]). If
NMI is not enabled while in SMM, the CPU latches one
NMI event and services the interrupt after NMI has been
enabled or after exiting SMM through the RSM instruction.
Upon entering SMM, the processor is in real mode, but it
may exit to either real or protected mode depending on its
state when SMM was initiated. The SMM header indicates
to which state it will exit.
Within the SMM service routine, protected mode may be
entered and exited as required, and real or protected
mode device drivers may be called.
To exit the SMM service routine, an RSM instruction,
rather than an IRET, is executed. The RSM instruction
causes the GXLV processor core to restore the CPU state
using the SMM header information and resume execution
at the interrupted point. If the full CPU state was saved by
the programmer, the stored values should be reloaded
before executing the RSM instruction using the MOV,
RSDC, RSLDT and RSTS instructions.
3.7.8.1
The SMI mechanism supports nesting of SMI interrupts
through the SMM service routine the SMI_NEST bit in the
CCR4 register (Index E8h[6]), and the Nested SMI Status
bit (bit N in the SMM header, see Table 3-35 "SMM Mem-
ory Space Header Description" on page 86). Nesting is an
important capability in allowing high-priority events, such
as audio virtualization, to interrupt lower-priority SMI code
for VGA virtualization or power management. SMI_NEST
controls whether SMI interrupts can occur during SMM.
SMM service routines can optionally set SMI_NEST high
to allow higher-priority SMI interrupts while handling the
current event.
SMI Nesting
The SMM service routine is responsible for managing the
SMM header data for nested SMI interrupts. The SMM
header must be saved before SMI_NEST is set high, and
SMI_NEST must be cleared and its header information
restored before an RSM instruction is executed.
The Nested SMI Status bit has been added to the SMM
header to show whether the current SMI is nested. The
processor sets Nested SMI Status high if the processor
was in SMM when the SMI was taken. The processor
uses Nested SMI Status on exit to determine whether the
processor should stay in SMM.
相關PDF資料 |
PDF描述 |
|---|---|
| 300471U | Radial, -55dotc, long life wsitching-power |
| 300CNQ | SCHOTTKY RECTIFIER |
| 300CNQ035 | SCHOTTKY RECTIFIER |
| 300CNQ040 | SCHOTTKY RECTIFIER |
| 300CNQ045 | SCHOTTKY RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 30046-46L | 制造商:LENOX 功能描述:HOLE SAW BI-METAL 73MM |
| 300-466A | 制造商:LG Corporation 功能描述:CABINET ASSYCMT-9325 |
| 300-466B | 制造商:LG Corporation 功能描述:CABINET ASSYCMT-9324 |
| 300-466K | 制造商:LG Corporation 功能描述:CABINET ASSYCMT-9322 |
| 300-466R | 制造商:LG Corporation 功能描述:FRONT CABINET |
發布緊急采購，3分鐘左右您將得到回復。