- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT16C854 (Exar Corporation) 2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO PDF資料下載
參數資料
| 型號： | XRT16C854 |
| 廠商： | Exar Corporation |
| 英文描述： | 2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO |
| 中文描述： | 2.97V至5.5V四路UART的128字節FIFO |
| 文件頁數： | 29/54頁 |
| 文件大?。?/td> | 485K |
| 代理商： | XRT16C854 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
xr
REV. 3.0.1
XR16C854/854D
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
29
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = one)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load.
Table 11
below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
The FCTR Bits 5-4 are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive
FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the
trigger level.
Table 11
shows the complete selections. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
T
ABLE
11: T
RANSMIT
AND
R
ECEIVE
FIFO T
RIGGER
L
EVEL
S
ELECTION
FCTR
B
IT
-5
FCTR
B
IT
-4
FCR
B
IT
-7
FCR
B
IT
-6
FCR
B
IT
-5
FCR
BIT
-4
R
ECEIVE
T
RIGGER
L
EVEL
T
RANSMIT
T
RIGGER
L
EVEL
C
OMPATIBILITY
0
0
0
0
1
1
0
1
0
1
0
0
1 (default)
4
8
14
1 (default)
Table-A. 16C550, 16C2550,
16C2552, 16C554, 16C580
compatible.
0
1
0
0
1
1
0
1
0
1
0
0
1
1
0
1
0
1
8
16
24
28
16
8
24
30
Table-B. 16C650A compatible.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT16L2552 | 2.25V TO 5.5V DUART WITH 16-BYTE FIFO |
| XRT3591 | SINGLECHIP V. 35 TRANSCEIVER |
| XRT3591B | SINGLECHIP V. 35 TRANSCEIVER |
| XRT3591BID | SINGLECHIP V. 35 TRANSCEIVER |
| XRT3591BIP | SINGLECHIP V. 35 TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT16L2552 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 16-BYTE FIFO |
| XRT2588CN | 制造商:Exar Corporation 功能描述: |
| XR-T2713CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Metering/Monitoring Circuit |
| XR-T3588 | 制造商:EXAR 制造商全稱:EXAR 功能描述:V.35 Interface Receiver/Transmitter |
| XR-T3588-89ES | 制造商:EXAR 制造商全稱:EXAR 功能描述:XR-T3588/89 Evaluation System |
發布緊急采購，3分鐘左右您將得到回復。