參數資料
型號: XR17C152CM-0A-EVB
廠商: Exar Corporation
文件頁數: 8/62頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR17C152 100TQFP
標準包裝: 1
系列: *
XR17C152
á
5V PCI BUS DUAL UART
REV. 1.2.0
16
1.2.6
SLEEP [31:24] - (default 0x00)
The 8-bit Sleep register enables each UART separately to enter Sleep mode. Sleep mode reduces power
consumption when the system needs to put the UART(s) to idle. All of these conditions must be satisfied for
the 152 to enter sleep mode:
no interrupts pending (INT0 = 0x00)
divisor is a non-zero value for both channels (ie. DLL = 0x1)
sleep mode is enabled (SLEEP = 0x03)
modem inputs for both channels are not toggling (MSR bits 0-3 = 0)
RX input pins for both channels are idling HIGH
The 152 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 152 resumes normal operation by any of the following:
a receive data start bit transition (logic HIGH to LOW)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 152 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the 152 is awakened by the modem inputs, a read
to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an
interrupt is pending from any channel. The 152 will stay in the sleep mode of operation until it is disabled by
setting Sleep = 0x00. In this case, the dual UART is awaken by any of the UART channel on from a receive
data byte or a change on the serial port. The UART is ready after 32 crystal clocks to ensure full functionality.
Also, a special interrupt is generated with an indication of no pending interrupt. Reading INT0 will clear this
special interrupt. Logic 0 (default) is disable and logic 1 is enable to sleep mode.
1.2.7
Device Identification and Revision
There are two internal registers that provide device identification and revision, DVID and DREV registers. The
8-bit content in the DVID register provides device identification. A return value of 0x22 from this register
indicates the device is an XR17C152 or an XR17D152. The DREV register returns an 8-bit value of 0x01 for
revision A with 0x02 equals to revision B and so forth. This information is very useful to the software driver for
identifying which device it is communicating with and to keep up with revision changes.
DVID [15:8]
Device identification for the type of UART. The upper nibble indicates it is an XR17Cxxx or XR17Dxxx series
device with lower nibble indicating the number of channels.
Examples:
XR17C158 or XR17D158 = 0x28
XR17C154 or XR17D154 = 0x24
XR17C152 or XR17D152 = 0x22
DREV [7:0]
Revision number of the XR17C152. A 0x01 represents "revision-A" with 0x02 for rev-B and so forth.
SLEEP Register
Individual UART Channel Sleep Enable
Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
Rsvd
Rsvd Rsvd Ch-1 Ch-0
Rsvd Rsvd Rsvd
相關PDF資料
PDF描述
VE-J52-EX CONVERTER MOD DC/DC 15V 75W
SI3056SSI2-EVB BOARD EVAL SI3056/SI3010 SSI
6828281-2 CA 62.5 SC DUP-MTRJ OR SECURE
RHS0E152MCN1GS CAP ALUM 1500UF 2.5V 20% SMD
RBM15DTKD-S288 CONN EDGECARD 30POS .156 EXTEND
相關代理商/技術參數
參數描述
XR17C152CM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C152IM 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART
XR17C152IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17C154 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART
XR17C154_05 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART