- 您現在的位置：買賣IC網 > PDF目錄16512 > XR17C152CM-0A-EVB (Exar Corporation)EVAL BOARD FOR XR17C152 100TQFP PDF資料下載
參數資料
| 型號： | XR17C152CM-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 39/62頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR17C152 100TQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
XR17C152
á
5V PCI BUS DUAL UART
REV. 1.2.0
44
4.8.12
SCRATCH PAD REGISTER (SPR) - Read/Write
This is an 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.8.13
FEATURE CONTROL REGISTER (FCTR) - Read/Write
FCTR [3:0] - Auto RTS/DTR Flow Control Hysteresis Select
These bits select the auto RTS/DTR flow control hysteresis and only valid when TX and RX Trigger Table-D is
selected (FCTR bit-6 and 7 are set to logic 1). The RTS/DTR hysteresis is referenced to the RX FIFO trigger
level. After reset, these bits are set to logic 0 selecting the next FIFO trigger level for hardware flow control.
Table 17 shows the 16 selectable hysteresis levels.
FCTR[4]: Infrared RX Input Logic Select
Logic 0 = Select RX input as active high encoded IrDA data, normal, (default).
Logic 1 = Select RX input as active low encoded IrDA data, inverted.
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes its logic level from HIGH to
LOW when finished sending the last stop bit of the last character out of the TSR register. It changes back to
HIGH from LOW when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior
sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register
(TSR) empty.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS#/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See Table 14 for complete selection with FCR bit 4-5 and FCTR
bit 6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR# output will
de-assert at 60 and re-assert at 16.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J52-EX | CONVERTER MOD DC/DC 15V 75W |
| SI3056SSI2-EVB | BOARD EVAL SI3056/SI3010 SSI |
| 6828281-2 | CA 62.5 SC DUP-MTRJ OR SECURE |
| RHS0E152MCN1GS | CAP ALUM 1500UF 2.5V 20% SMD |
| RBM15DTKD-S288 | CONN EDGECARD 30POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17C152CM-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17C152IM | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS DUAL UART |
| XR17C152IM-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17C154 | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART |
| XR17C154_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V PCI BUS QUAD UART |
發布緊急采購，3分鐘左右您將得到回復。