參數資料
型號： XBIB-U
廠商： Digi International/Maxstream
文件頁數： 41/72頁
文件大?。?/td> 1116K
描述： BOARD USB ZIGBEE MOD PRO
設計資源： XBIB-U Shematic
標準包裝： 1
附件類型： 接口板
適用于相關產品： XBee 和 XBee Pro 收音機
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?1
Chapter??燫F燤odule燙onfiguration
DL (Destination Address Low) Command
<Networking {Addressing}> The DL command is
used to set and read the lower 32 bits of the RF
module's 64-bit destination address. When com-
bined with the DH (Destination Address High)
for transmission.
A module will only communicate with other mod-
ules having the same channel (CH parameter),
PAN ID (ID parameter) and destination address (DH + DL parameters).
To transmit using a 16-bit address, set the DH parameter to zero and the DL parameter less than
0xFFFF. 0x000000000000FFFF (DL concatenated to DH) is the broadcast address for the PAN.
Refer to the XBee/XBee-PRO Addressing section for more information.
DN (Destination Node) Command
<Networking {Identification}> The DN command
is used to resolve a NI (Node Identifier) string to
a physical address. The following events occur
upon successful command execution:
1. DL and DH are set to the address of the
module with the matching NI (Node Identifier).
2. OK is returned.
3. RF module automatically exits AT Command Mode.
If there is no response from a modem within 200 msec or a parameter is not specified (left blank),
the command is terminated and an ERROR message is returned.
DP (Disassociation Cyclic Sleep Period) Command
<Sleep Mode (Low Power)>
NonBeacon Firmware
End Device - The DP command is used to set and 
read the time period of sleep for cyclic sleeping
remotes that are configured for Association but
are not associated to a Coordinator. (i.e. If a
device is configured to associate, configured as a
Cyclic Sleep remote, but does not find a Coordi-
nator; it will sleep for DP time before reattempt-
ing association.) Maximum sleep period is 268
seconds (0x68B0). DP should be > 0 for NonBeacon systems.
EA (ACK Failures) Command
<Diagnostics> The EA command is used to reset
and read the count of ACK (acknowledgement)
failures. This parameter value increments when
the module expires its transmission retries with-
out receiving an ACK on a packet transmission.
This count saturates at its maximum value.
Set the parameter to 0 to reset count.
AT Command: ATDL
Parameter Range: 0 - 0xFFFFFFFF
Default Parameter Value: 0
Related Commands: DH (Destination Address
High), CH (Channel), ID (PAN VID), MY (Source
Address)
AT Command: ATDN
Parameter Range: 20-character ASCII String
Minimum Firmware Version Required: v1.x80
AT Command: ATDP
Parameter Range: 1 - 0x68B0
 [x 10 milliseconds]
Default Parameter Value:0x3E8
(1000 decimal)
Related Commands: SM (Sleep Mode), SP
(Cyclic Sleep Period), ST (Time before Sleep)
Minimum Firmware Version Required: v1.x80
AT Command: ATEA
Parameter Range:0 - 0xFFFF
Minimum Firmware Version Required: v1.x80
相關PDF資料
PDF描述
XIB-E BOARD INTERFACE ETHERNET
XIB-R BOARD INTERFACE RS232/485
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
相關代理商/技術參數
參數描述
XBIB-U-DEV 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SP 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBIB-U-SS 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XBL6450BYFVR 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel
XBL6450YFHR 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*