- 您現在的位置：買賣IC網 > Datasheet目錄58 > XBIB-U (Digi International/Maxstream)BOARD USB ZIGBEE MOD PRO Datasheet資料下載
參數資料
| 型號： | XBIB-U |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 36/72頁 |
| 文件大小： | 1116K |
| 描述： | BOARD USB ZIGBEE MOD PRO |
| 設計資源： | XBIB-U Shematic |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XBee 和 XBee Pro 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?6
Chapter??燫F燤odule燙onfiguration
AP (API Enable) Command
<Serial Interfacing> The AP command is used to
enable the RF module to operate using a frame-
based API instead of using the default Transpar-
ent (UART) mode.
Refer to the API Operation section when API operation is enabled (AP = 1 or 2).
AS (Active Scan) Command
<AT Command Mode Options> The AS command
is used to send a Beacon Request to a Broadcast
(0xFFFF) and Broadcast PAN (0xFFFF) on every
channel. The parameter determines the amount
of time the RF module will listen for Beacons on
each channel. A PanDescriptor is created and
returned for every Beacon received from the
scan. Each PanDescriptor contains the following
information:
CoordAddress (SH + SL parameters) (NOTE: If MY on the coordinator is set less than
0xFFFF, the MY value is displayed)
CoordPanID (ID parameter)
CoordAddrMode
0x02 = 16-bit Short Address
0x03 = 64-bit Long Address
Channel (CH parameter)
SecurityUse
ACLEntry
SecurityFailure
SuperFrameSpec (2 bytes):
bit 15 - Association Permitted (MSB)
bit 14 - PAN Coordinator
bit 13 - Reserved
bit 12 - Battery Life Extension
bits 8-11 - Final CAP Slot
bits 4-7 - Superframe Order
bits 0-3 - Beacon Order
GtsPermit
RSSI (- RSSI is returned as -dBm)
TimeStamp (3 bytes)
<CR> (A carriage return is sent at the end of the AS command.
The Active Scan is capable of returning up to 5 PanDescriptors in a scan. The actual scan time on
each channel is measured as Time = [(2 ^ (SD Parameter)) * 15.36] ms. Total scan time is this
time multiplied by the number of channels to be scanned (16 for the XBee, 12 for the XBee-PRO).
NOTE: Refer the scan table in the SD description to determine scan times. If using API Mode, no
<CR>s are returned in the response. Refer to the API Mode Operation section.
AT Command: ATAP
Parameter Range:0 - 2
Parameter
Configuration
0
Disabled
(Transparent operation)
1
API enabled
2
API enabled
(with escaped characters)
Default Parameter Value:0
Minimum Firmware Version Required: v1.x80
AT Command: ATAS
Parameter Range: 0 - 6
Related Command: SD (Scan Duration), DL
(Destination Low Address), DH (Destination
High Address), ID (PAN ID), CH (Channel)
Minimum Firmware Version Required: v1.x80
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-E | BOARD INTERFACE ETHERNET |
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XBIB-U-DEV | 功能描述:界面開發工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SP | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBIB-U-SS | 功能描述:界面開發工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XBL6450BYFVR | 制造商:Texas Instruments 功能描述:ECS BLUELINK - Tape and Reel |
| XBL6450YFHR | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。