- 您現在的位置：買賣IC網 > PDF目錄361799 > W9968CF Digital Camera PDF資料下載
參數資料
| 型號： | W9968CF |
| 英文描述： | Digital Camera |
| 中文描述： | 數碼相機 |
| 文件頁數： | 34/78頁 |
| 文件大小： | 814K |
| 代理商： | W9968CF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
W9968CF
- 34 -
7.5 Video/Still Image Data Transfer
Video or still image data from the device is delivered to the host system through an isochronous pipe
(Endpoint 1). The maximum packet size can be varied for different alternate settings for limited USB
bandwidth for other USB devices.
7.5.1 Output Video Data Format
The W9968CF supports two video transfer modes: original video transfer mode and JPEG
compression video transfer mode. The captured video stored in the DRAM will be compressed by the
JPEG encoder and then transferred to the host if JPEG compression video transfer mode is selected,
or will be directly transferred to the host if original video transfer mode is selected. Four different
formats are supported for the output video which are selected by bits 1-0 of the Video Capture Control
register (CR26) and bits 1 of the JPEG Encoder Control register (CR39) as described in Table 7.13.
Table 7.13 Output Video Data Format
CR39_1
CR26_1-0
Output Video Data Format
0
00
Original YUV4:2:2 packed mode
0
01
Original YUV4:2:0 packed mode
1
0X
Reserved
1
10
JPEG YUV4:2:2 non-interleaved scan mode
1
11
JPEG YUV4:2:0 non-interleaved scan mode
7.5.2 Video Frame Synchronization
A single video frame typically requires multiple USB packets. One or more zero length isochronous
data packets are used to mark the end of a video frame. The first non-zero data packet is the start of
the next video frame.
f an error is encountered during the reception of a USB packet, the host may discard the entire video
frame. Processing begins again with the next video frame as indicated by the first non-zero length
isochronous data packet after one or more zero-length packet.
7.5.3 Bandwidth Management
The W9968CF provides for varying the bandwidth required by providing a zero-bandwidth interface
(alternate setting zero) and 16 alternate settings interfaces with 8 Mbps down to 0.5 Mbps bandwidth in
descending 0.5 Mbps steps. The default alternate setting zero (with zero bandwidth) selected by a Set
Configuration request allows a video camera to be initially configured even on a highly utilized USB bus.
Before the device begins streaming video data, the host software must select an alternate setting with
the appropriate amount of bandwidth by using the Set Interface request.
相關PDF資料 |
PDF描述 |
|---|---|
| W9N150V | N-channel 1500V - 2.2ヘ - 8A - TO-247 Very high voltage PowerMESH⑩ Power MOSFET |
| WA-A240PAI | Peripheral Interface |
| WA-A240PAM | Peripheral Interface |
| WA-A233CBC | Peripheral Interface |
| WA-A233CBI | Peripheral Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W9986D | 制造商:WINBOND 制造商全稱:Winbond 功能描述:MPEG Audio Layer III Decoder |
| W99ABX-6 | 制造商:Magnecraft 功能描述: |
| W99ADBX-2 | 制造商:Magnecraft 功能描述: |
| W99ADX-1 | 制造商:Magnecraft 功能描述: |
| W99AX-10 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。