參數資料
型號： W971GG6IB-25
廠商： WINBOND ELECTRONICS CORP
元件分類： DRAM
英文描述： 32M X 16 DDR DRAM, 0.4 ns, PBGA84
封裝： 8 X 12.50 MM, ROHS COMPLIANT, WBGA-84
文件頁數： 3/86頁
文件大?。?/td> 1360K
代理商： W971GG6IB-25
W971GG6IB
Publication Release Date: Oct. 23, 2009
- 11 -
Revision A02
A[2:0] with options of 4 and 8 bit burst lengths. The burst length decodes are compatible with DDR
SDRAM. Burst address sequence type is defined by A3, CAS Latency is defined by A[6:4]. The DDR2
does not support half clock latency mode. A7 is used for test mode. A8 is used for DLL reset. A7 must
be set to LOW for normal MRS operation. Write recovery time WR is defined by A[11:9]. Refer to the
table for specific codes.
DD
R2-667
(-3)
DD
R2-800
(-25)
DDR
2-1066
(-18)
DDR
2-800
(-
25)
DD
R2-106
6(-18)
DDR
2-667
(-
3)
Note:
1. WR (write recovery for Auto-precharge) min is determined by tCK(avg) max and WR max is determined by tCK(avg) min.
WR[cycles] = RU{ tWR[nS] / tCK(avg)[nS] }, where RU stands for round up. The mode register must be programmed to this
value. This is also used with tRP to determine tDAL.
Figure 2—Mode Register Set (MRS)
7.2.2
Extend Mode Register Set Commands (EMRS)
7.2.2.1
Extend Mode Register Set Command (1), EMR (1)
( CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "H", BA1 = "L, BA2 = "L" A0 to A12 =
Register data)
The extended mode register (1) stores the data for enabling or disabling the DLL, output driver
strength, additive latency, ODT, DQS disable, OCD program. The default value of the extended
mode register (1) is not defined, therefore the extended mode register (1) must be programmed during
initialization for proper operation. The DDR2 SDRAM should be in all bank precharge with CKE
already high prior to writing into the extended mode register (1). The mode register set command
cycle time (tMRD) must be satisfied to complete the write operation to the extended mode register (1).
Extended mode register (1) contents can be changed using the same command and clock cycle
requirements during normal operation as long as all banks are in the precharge state. A0 is used for
DLL enable or disable. A1 is used for enabling a reduced strength output driver. A[5:3] determines the
additive latency, A[9:7] are used for OCD control, A10 is used for DQS disable. A2 and A6 are used
for ODT setting.
相關PDF資料
PDF描述
W9751G6JB-25A 32M X 16 DDR DRAM, 0.4 ns, PBGA84
W9751G8JB-18 DDR DRAM, PBGA84
W9812G21H-6I 4M X 32 SYNCHRONOUS DRAM, 5 ns, PDSO86
W9812G21H-6C 4M X 32 SYNCHRONOUS DRAM, 4.5 ns, PDSO86
W9812G6JH-6 8M X 16 SYNCHRONOUS DRAM, 5 ns, PDSO54
相關代理商/技術參數
參數描述
W971GG6JB 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M ? 8 BANKS ? 16 BIT DDR2 SDRAM
W971GG6JB-18 制造商:Winbond Electronics Corp 功能描述:1GB DDR2 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 1GBIT 1.875NS
W971GG6JB-25 制造商:Winbond Electronics Corp 功能描述:DRAM Chip DDR2 SDRAM 1G-Bit 64Mx16 1.8V 84-Pin WBGA 制造商:Winbond Electronics 功能描述:64MBX16 DDR2 制造商:Winbond 功能描述:DRAM Chip DDR2 SDRAM 1G-Bit 64Mx16 1.8V 84-Pin WBGA
W971GG6JB25I 功能描述:IC DDR2 SDRAM 1GBIT 84WBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:3,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K (4K x 8) 速度:100kHz，400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) 其它名稱:CAV24C32WE-GT3OSTR
W971GG6JB-25I 制造商:Winbond Electronics 功能描述:-40~85 1GB DDR2 FOR INDUSTRY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*