參數資料
型號： W83977TF(EOL)
英文描述： W83877TF plus KBC. CIR. RTC
中文描述： W83877TF加比聯。稅務局局長。時鐘
文件頁數： 85/161頁
文件大小： 592K
代理商： W83977TF(EOL)
W83977EF/ CTF
PRELIMINARY
Publication Release Date: March 1999
-76 -
Revision A1
5.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol
before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The
following are required:
(a) Set direction = 0, enabling the drivers.
(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
(c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
(d) Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,
respectively.
5.3.13.1 Mode Switching
Software will execute P1284 negotiation and all operations prior to a data transfer phase under
programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake,
moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010).
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001
it can only be switched into mode 000 or 001. The direction can be changed only in mode 001.
When in extended forward mode, the software should wait for the FIFO to be empty before switching
back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the
FIFO before changing back to mode 000 or 001.
5.3.13.2 Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction,
normal data are transferred when HostAck is high and an 8-bit command is transferred when HostAck
is low. The most significant bits of the command indicate whether it is a run-length count (for
compression) or a channel address.
In the reverse direction, normal data are transferred when PeriphAck is high and an 8-bit command is
transferred when PeriphAck is low. The most significant bit of the command is always zero.
5.3.13.3 Data Compression
The W83977EF/CTF supports run length encoded (RLE) decompression in hardware and can transfer
compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported.
In order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data
byte is written to the ecpDFifo.
5.3.14 FIFO Operation
The FIFO threshold is set in configuration register 5. All data transfers to or from the parallel port can
proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO
is used by selecting the Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO
is disabled.
相關PDF資料
PDF描述
W83C42 KEYBOARD CONTROLLER
W83C42P KEYBOARD CONTROLLER
W83C45 Keyboard Controller
W83C45P Keyboard Controller
W83C553F-G W83C553F-G Highly Integrated System I/O Controller for Power PCTM (South Bridge) QFP 208
相關代理商/技術參數
參數描述
W83977TF-P 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter
W83977TF-PW 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter
W83C42 制造商:WINBOND 制造商全稱:Winbond 功能描述:KEYBOARD CONTROLLER
W83C42P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:KEYBOARD CONTROLLER
W83C43 制造商:WINBOND 制造商全稱:Winbond 功能描述:KEYBOARD CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*