- 您現在的位置：買賣IC網 > PDF目錄361795 > W83977TF(EOL) W83877TF plus KBC. CIR. RTC PDF資料下載
參數資料
| 型號： | W83977TF(EOL) |
| 英文描述： | W83877TF plus KBC. CIR. RTC |
| 中文描述： | W83877TF加比聯。稅務局局長。時鐘 |
| 文件頁數： | 29/161頁 |
| 文件大小： | 592K |
| 代理商： | W83977TF(EOL) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
W83977EF/ CTF
PRELIMINARY
Publication Release Date: March 1999
-20 -
Revision A1
At the start of a command the FIFO is always disabled and command parameters must be sent based
upon the RQM and DIO bit settings in the main status register. When the FDC enters the command
execution phase, it clears the FIFO of any data to ensure that invalid data are not transferred.
An overrun and underrun will terminate the current command and the data transfer. Disk writes will
complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to
remove the remaining data so that the result phase may be entered.
DMA transfers are enabled with the SPECIFY command, and are initiated by the FDC by activating
the DRQ pin during a data transfer command. The FIFO is enabled directly by asserting DACK# and
addresses need not be valid.
Note that if the DMA controller is programmed to function in verify mode, a pseudo read is performed
by the FDC based only onDACK#. This mode is only available when the FDC has been configured
into byte mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled the above
operation is performed by using the new VERIFY command. No DMA operation is needed.
2.1.3 Data Separator
The function of the data separator is to lock onto the incoming serial read data. When a lock is
achieved the serial front end logic of the chip is provided with a clock which is synchronized to the
read data. The synchronized clock, called the Data Window, is used to internally sample the serial
data portion of the bit cell, and the alternate state samples the clock portion. Serial to parallel
conversion logic separates the read data into clock and data bytes.
The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking.
The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized
and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for
every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on
speed. A digital integrator is used to keep track of the speed changes in the input data stream.
2.1.4 Write Precompensation
The write precompensation logic is used to minimize bit shifts in the RDDATA stream from the disk
drive. Shifting of bits is a known phenomenon in magnetic media and is dependent on the disk media
and the floppy drive.
The FDC monitors the bit stream that is being sent to the drive. The data patterns that require
precompensation are well known. Depending upon the pattern, the bit is shifted either early or late
relative to the surrounding bits.
相關PDF資料 |
PDF描述 |
|---|---|
| W83C42 | KEYBOARD CONTROLLER |
| W83C42P | KEYBOARD CONTROLLER |
| W83C45 | Keyboard Controller |
| W83C45P | Keyboard Controller |
| W83C553F-G | W83C553F-G Highly Integrated System I/O Controller for Power PCTM (South Bridge) QFP 208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83977TF-P | 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter |
| W83977TF-PW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:I/O chip disk drive adapter |
| W83C42 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:KEYBOARD CONTROLLER |
| W83C42P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:KEYBOARD CONTROLLER |
| W83C43 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:KEYBOARD CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。