- 您現在的位置：買賣IC網 > PDF目錄140352 > W3E32M64S-200SBI (WHITE ELECTRONIC DESIGNS CORP) 32M X 64 DDR DRAM, 0.8 ns, PBGA208 PDF資料下載
參數資料
| 型號： | W3E32M64S-200SBI |
| 廠商： | WHITE ELECTRONIC DESIGNS CORP |
| 元件分類： | DRAM |
| 英文描述： | 32M X 64 DDR DRAM, 0.8 ns, PBGA208 |
| 封裝： | 13 X 22 MM, PLASTIC, BGA-208 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 648K |
| 代理商： | W3E32M64S-200SBI |
6
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W3E32M64S-XSBX
January 2008
Rev. 6
be followed by a LOAD MODE REGISTER command to the
mode register (BA0/BA1 both LOW) to reset the DLL.
TABLE 2 – CAS LATENCY
ALLOWABLE OPERATING FREQUENCY (MHz)
SPEED
CAS LATENCY = 2 CAS LATENCY = 2.5 CAS LATENCY = 3
-200
≤ 75
≤ 100
—
-250
≤ 100
≤ 125
—
-266
≤ 100
≤ 133
—
-333 (IND)
—
≤ 166
-333 (MIL)
—
≤ 133
≤ 166
The extended mode register must be loaded when all
banks are idle and no bursts are in progress, and the
controller must wait the specified time before initiating
any subsequent operation. Violating either of these
requirements could result in unspecified operation.
OUTPUT DRIVE STRENGTH
The normal full drive strength for all outputs are specified to
be SSTL2, Class II. The DDR SDRAM supports an option
for reduced drive. This option is intended for the support
of the lighter load and/or point-to-point environments. The
selection of the reduced drive strength will alter the DQs
and DQSs from SSTL2, Class II drive strength to a reduced
drive strength, which is approximately 54 percent of the
SSTL2, Class II drive strength.
DLL ENABLE/DISABLE
When the part is running without the DLL enabled, device
functionality may be altered. The DLL must be enabled for
normal operation. DLL enable is required during power-
up initialization and upon returning to normal operation
after having disabled the DLL for the purpose of debug or
evaluation. (When the device exits self refresh mode, the
DLL is enabled automatically.) Any time the DLL is enabled,
200 clock cycles with CKE high must occur before a READ
command can be issued.
COMMANDS
The Truth Table provides a quick reference of available
commands. This is followed by a written description of
each command.
DESELECT
The DESELECT function (CS# High) prevents new
commands from being executed by the DDR SDRAM. The
SDRAM is effectively deselected. Operations already in
progress are not affected.
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform
a NOP to the selected DDR SDRAM (CS# is LOW while
RAS#, CAS#, and WE# are high). This prevents unwanted
commands from being registered during idle or wait states.
Operations already in progress are not affected.
LOAD MODE REGISTER
The Mode Registers are loaded via inputs A0-12. The
LOAD MODE REGISTER command can only be issued
when all banks are idle, and a subsequent executable
command cannot be issued until tMRD is met.
ACTIVE
The ACTIVE command is used to open (or activate) a
row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and the
address provided on inputs A0-12 selects the row. This row
remains active (or open) for accesses until a PRECHARGE
command is issued to that bank. A PRECHARGE
command must be issued before opening a different row
in the same bank.
READ
The READ command is used to initiate a burst read access
to an active row. The value on the BA0, BA1 inputs selects
the bank, and the address provided on inputs A0-9 selects
the starting column location. The value on input A10
determines whether or not AUTO PRECHARGE is used. If
AUTO PRECHARGE is selected, the row being accessed
will be precharged at the end of the READ burst; if AUTO
PRECHARGE is not selected, the row will remain open
for subsequent accesses.
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1 inputs
selects the bank, and the address provided on inputs A0-9
selects the starting column location. The value on input A10
determines whether or not AUTO PRECHARGE is used. If
AUTO PRECHARGE is selected, the row being accessed
will be precharged at the end of the WRITE burst; if AUTO
PRECHARGE is not selected, the row will remain open for
subsequent accesses. Input data appearing on the D/Qs
is written to the memory array subject to the DQM input
logic level appearing coincident with the data. If a given
DQM signal is registered LOW, the corresponding data
will be written to memory; if the DQM signal is registered
相關PDF資料 |
PDF描述 |
|---|---|
| W3EG6433S262BD4 | 32M X 64 DDR DRAM MODULE, 0.75 ns, DMA200 |
| WS57C256F-35C | 32K X 8 UVPROM, 35 ns, CQCC32 |
| WF128K32A-120HSI | 512K X 8 FLASH 12V PROM MODULE, 120 ns, CHIP66 |
| WF512K32-90HI5 | 512K X 32 FLASH 5V PROM MODULE, 90 ns, CHIP66 |
| WMF2M8-90OPM5 | 2M X 8 FLASH 5V PROM, 90 ns, CDSO56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W3E32M64S-200SBM | 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 200 MHZ, 208 PBGA, MIL-TEMP. - Bulk |
| W3E32M64S-250BC | 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, COMMERCIAL TEMP. - Bulk |
| W3E32M64S-250BI | 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, INDUSTRIAL TEMP. - Bulk |
| W3E32M64S-250BM | 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, MIL-TEMP. - Bulk |
| W3E32M64S-250SBC | 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 208 PBGA, COMMERCIAL TEMP. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。