參數資料
型號: W3E32M64S-200SBI
廠商: WHITE ELECTRONIC DESIGNS CORP
元件分類: DRAM
英文描述: 32M X 64 DDR DRAM, 0.8 ns, PBGA208
封裝: 13 X 22 MM, PLASTIC, BGA-208
文件頁數: 13/18頁
文件大?。?/td> 648K
代理商: W3E32M64S-200SBI
4
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W3E32M64S-XSBX
January 2008
Rev. 6
A0-12
BA0-1
CLK0
CLK
CAS
DQ0
DQ15
CKE0
CKE
CS0
CS
DQML0
DQML
DQMH0
DQMH
RAS1
WE1
CAS1
DQ0
DQ15
WE
U1
RAS
A0-12
BA0-1
CLK1
CLK
CAS
DQ16
DQ31
RAS0
WE0
CAS0
DQ0
DQ15
WE
U0
RAS
CKE1
CKE
CS1
CS
DQML1
DQML
DQMH1
DQMH
RAS2
WE2
CAS2
DQ0
DQ15
WE
U2
RAS
A0-12
BA0-1
CLK2
CLK
CAS
DQ32
DQ47
CKE2
CKE
CS2
CS
DQML2
DQML
DQMH2
DQMH
RAS3
WE3
CAS3
DQ0
DQ15
WE
U3
RAS
A0-12
BA0-1
CLK3
CLK
CAS
DQ48
DQ63
CKE3
CKE
CS3
CS
DQSL3
DQSL
DQSH3
DQSH
Y=
CLK3
CLK
VREF
DQSL2
DQSL
DQSH2
DQSH
VREF
DQSL1
DQSL
DQSH1
DQSH
VREF
DQSL0
DQSL
DQSH0
DQSH
VREF
CLK2
CLK
CLK1
CLK
CLK0
CLK
VREF
DQML3
DQML
DQMH3
DQMH
FIGURE 2 FUNCTIONAL BLOCK DIAGRAM
INITIALIZATION
DDR SDRAMs must be powered up and initialized in a
predefined manner. Operational procedures other than
those specified may result in undefined operation. Power
must first be applied to VCC and VCCQ simultaneously, and
then to VREF (and to the system VTT). VTT must be applied
after VCCQ to avoid device latch-up, which may cause
permanent damage to the device. VREF can be applied any
time after VCCQ but is expected to be nominally coincident
with VTT. Except for CKE, inputs are not recognized as
valid until after VREF is applied. CKE is an SSTL_2 input
but will detect an LVCMOS LOW level after VCC is applied.
After CKE passes through VIH, it will transition to an
SSTL_2 signal and remain as such until power is cycled.
Maintaining an LVCMOS LOW level on CKE during power-
up is required to ensure that the DQ and DQS outputs will
be in the High-Z state, where they will remain until driven
in normal operation (by a read access). After all power
supply and reference voltages are stable, and the clock
is stable, the DDR SDRAM requires a 200μs delay prior
to applying an executable command.
Once the 200μs delay has been satisfied, a DESELECT
or NOP command should be applied, and CKE should
be brought HIGH. Following the NOP command, a
PRECHARGE ALL command should be applied. Next a
LOAD MODE REGISTER command should be issued for
the extended mode register (BA1 LOW and BA0 HIGH)
to enable the DLL, followed by another LOAD MODE
REGISTER command to the mode register (BA0/BA1
both LOW) to reset the DLL and to program the operating
parameters. Two-hundred clock cycles are required
between the DLL reset and any READ command. A
PRECHARGE ALL command should then be applied,
placing the device in the all banks idle state.
Once in the idle state, two AUTO REFRESH cycles must
be performed (tRFC must be satisfied.) Additionally, a LOAD
MODE REGISTER command for the mode register with
the reset DLL bit deactivated (i.e., to program operating
parameters without resetting the DLL) is required.
Following these requirements, the DDR SDRAM is ready
for normal operation.
相關PDF資料
PDF描述
W3EG6433S262BD4 32M X 64 DDR DRAM MODULE, 0.75 ns, DMA200
WS57C256F-35C 32K X 8 UVPROM, 35 ns, CQCC32
WF128K32A-120HSI 512K X 8 FLASH 12V PROM MODULE, 120 ns, CHIP66
WF512K32-90HI5 512K X 32 FLASH 5V PROM MODULE, 90 ns, CHIP66
WMF2M8-90OPM5 2M X 8 FLASH 5V PROM, 90 ns, CDSO56
相關代理商/技術參數
參數描述
W3E32M64S-200SBM 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 200 MHZ, 208 PBGA, MIL-TEMP. - Bulk
W3E32M64S-250BC 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, COMMERCIAL TEMP. - Bulk
W3E32M64S-250BI 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, INDUSTRIAL TEMP. - Bulk
W3E32M64S-250BM 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 219 PBGA, MIL-TEMP. - Bulk
W3E32M64S-250SBC 制造商:Microsemi Corporation 功能描述:32M X 64 DDR, 2.5V, 250 MHZ, 208 PBGA, COMMERCIAL TEMP. - Bulk