參數資料
型號： SJA1000
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Stand-alone CAN controller(單機CAN控制器)
中文描述： 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDIP28
封裝： 0.600 INCH, PLASTIC, DIP-28
文件頁數： 8/68頁
文件大?。?/td> 234K
代理商： SJA1000
2000 Jan 04
8
Philips Semiconductors
Product specification
Stand-alone CAN controller
SJA1000
6.2.1.3
Receive buffer
The dual receive buffer concept of the PCA82C200 is
replaced by the receive FIFO from the PeliCAN controller.
Thishasnoeffecttotheapplicationsoftwareexceptforthe
data overrun probability. Now more than two messages
may be received (up to 64 bytes) until a data overrun
occurs.
6.2.1.4
CAN 2.0B
The SJA1000 is designed to support the full CAN 2.0B
protocol specification, which means that the extended
oscillator tolerance is implemented as well as the
processing of extended frame messages. In BasicCAN
mode it is possible to transmit and receive standard frame
messages only (11-bit identifier). If extended frame
messages (29-bit identifier) are detected on the CAN-bus,
they are tolerated and an acknowledge is given if the
message was correct, but there is no receive interrupt
generated.
6.2.2
D
IFFERENCES BETWEEN
B
ASIC
CAN
AND
P
ELI
CAN
MODE
In the PeliCAN mode the SJA1000 appears with a
re-organized register mapping with a lot of new features.
All known bits from the PCA82C200 design are available
as well as several new ones. In the PeliCAN mode the
complete CAN 2.0B functionality is supported (29-bit
identifier).
Main new features of the SJA1000 are:
Reception and transmission of standard and extended
frame format messages
Receive FIFO (64-byte)
Single/dual acceptance filter with mask and code
register for standard and extended frame
Error counters with read/write access
Programmable error warning limit
Last error code register
Error interrupt for each CAN-bus error
Arbitration lost interrupt with detailed bit position
Single-shot transmission (no re-transmission on error or
arbitration lost)
Listen only mode (monitoring of the CAN-bus, no
acknowledge, no error flags)
Hot plugging supported (disturbance-free software
driven bit rate detection)
Disable CLKOUT by hardware.
6.3
BasicCAN mode
6.3.1
B
ASIC
CAN
ADDRESS LAYOUT
The SJA1000 appears to a microcontroller as a
memory-mapped I/O device. An independent operation of
both devices is guaranteed by a RAM-like implementation
of the on-chip registers.
The address area of the SJA1000 consists of the control
segment and the message buffers. The control segment is
programmed during an initialization download in order to
configure communication parameters (e.g. bit timing).
Communication over the CAN-bus is also controlled via
this segment by the microcontroller. During initialization
the CLKOUT signal may be programmed to a value
determined by the microcontroller.
A message, which should be transmitted, has to be written
to the transmit buffer. After a successful reception the
microcontroller may read the received message from the
receive buffer and then release it for further use.
The exchange of status, control and command signals
between the microcontroller and the SJA1000 is
performed in the control segment. The layout of this
segment is shown in Table 3. After an initial download, the
contents of the registers acceptance code, acceptance
mask, bus timing registers 0 and 1 and output control
should not be changed. Therefore these registers may
only be accessed when the reset request bit in the control
register is set HIGH.
For register access, two different modes have to be
distinguished:
Reset mode
Operating mode.
The reset mode (see Table 3, control register, bit Reset
Request) is entered automatically after a hardware reset
or when the controller enters the bus-off state (see
Table 5, status register, bit Bus Status). The operating
modeisactivatedbyresettingoftheresetrequestbitinthe
control register.
相關PDF資料
PDF描述
SJE1349 NPN PLASTIC POWER TRANSISTOR
SK016R SCRs
SK006V SCRs
SK008D Box-shaped pin header, Discrete wire crimping connection, Discrete wire connectors; HRS No: 543-0505-6 00; No. of Positions: 12; Connector Type: Wire; Contact Gender: Female; Contact Spacing (mm): 2; Terminal Pitch (mm): 2; Current Rating(Amps)(Max.): 2; Operating Temperature Range (degrees C): -30 to 85; General Description: Housing; For Discrete wire; Crimping
SK008L SCRs
相關代理商/技術參數
參數描述
SJA1000/N1,112 功能描述:網絡控制器與處理器 IC STAND-ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
SJA1000/N1112 制造商:NXP Semiconductors 功能描述:IC CAN CONTROLLER 1000 DIP28
SJA1000N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone CAN controller
SJA1000T 制造商:NXP Semiconductors 功能描述:
SJA1000T/N,112 功能描述:網絡控制器與處理器 IC STAND ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*