參數資料
型號： SJA1000
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Stand-alone CAN controller(單機CAN控制器)
中文描述： 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDIP28
封裝： 0.600 INCH, PLASTIC, DIP-28
文件頁數： 7/68頁
文件大?。?/td> 234K
代理商： SJA1000
2000 Jan 04
7
Philips Semiconductors
Product specification
Stand-alone CAN controller
SJA1000
6
FUNCTIONAL DESCRIPTION
6.1
Description of the CAN controller blocks
6.1.1
I
NTERFACE
M
ANAGEMENT
L
OGIC
(IML)
The interface management logic interprets commands
from the CPU, controls addressing of the CAN registers
and provides interrupts and status information to the host
microcontroller.
6.1.2
T
RANSMIT
B
UFFER
(TXB)
The transmit buffer is an interface between the CPU and
the Bit Stream Processor (BSP) that is able to store a
complete message for transmission over the CAN
network. The buffer is 13 bytes long, written to by the CPU
and read out by the BSP.
6.1.3
R
ECEIVE
B
UFFER
(RXB, RXFIFO)
The receive buffer is an interface between the acceptance
filter and the CPU that stores the received and accepted
messages from the CAN-bus line. The Receive Buffer
(RXB)representsaCPU-accessible13-bytewindowofthe
Receive FIFO (RXFIFO), which has a total length of
64 bytes.
With the help of this FIFO the CPU is able to process one
message while other messages are being received.
6.1.4
A
CCEPTANCE
F
ILTER
(ACF)
The acceptance filter compares the received identifier with
the acceptance filter register contents and decides
whether this message should be accepted or not. In the
eventofapositiveacceptancetest,thecompletemessage
is stored in the RXFIFO.
6.1.5
B
IT
S
TREAM
P
ROCESSOR
(BSP)
Thebitstreamprocessorisasequencerwhichcontrolsthe
data stream between the transmit buffer, RXFIFO and the
CAN-bus. It also performs the error detection, arbitration,
stuffing and error handling on the CAN-bus.
6.1.6
B
IT
T
IMING
L
OGIC
(BTL)
The bit timing logic monitors the serial CAN-bus line and
handles the bus line-related bit timing. It is synchronized to
the bit stream on the CAN-bus on a
‘recessive-to-dominant’ bus line transition at the beginning
of a message (hard synchronization) and re-synchronized
on further transitions during the reception of a message
(soft synchronization). The BTL also provides
programmable time segments to compensate for the
propagation delay times and phase shifts (e.g. due to
oscillator drifts) and to define the sample point and the
number of samples to be taken within a bit time.
6.1.7
E
RROR
M
ANAGEMENT
L
OGIC
(EML)
The EML is responsible for the error confinement of the
transfer-layer modules. It receives error announcements
from the BSP and then informs the BSP and IML about
error statistics.
6.2
Detailed description of the CAN controller
The SJA1000 is designed to be software and
pin-compatible to its predecessor, the PCA82C200
stand-alone CAN controller. Additionally, a lot of new
functions are implemented. To achieve the software
compatibility, two different modes of operation are
implemented:
BasicCAN mode; PCA82C200 compatible
PeliCAN mode; extended features.
The mode of operation is selected with the CAN-mode bit
located within the clock divider register. Default mode
upon reset is the BasicCAN mode.
6.2.1
PCA82C200
COMPATIBILITY
In BasicCAN mode the SJA1000 emulates all known
registers from the PCA82C200 stand-alone CAN
controller. The characteristics, as described in Sections
6.2.1.1 to 6.2.1.4 are different from the PCA82C200
design with respect to software compatibility.
6.2.1.1
Synchronization mode
The SYNC bit in the control register is removed (CR.6 in
the PCA82C200). Synchronization is only possible by a
recessive-to-dominant transition on the CAN-bus. Writing
to this bit has no effect. To achieve compatibility to existing
application software, a read access to this bit will reflect
the previously written value (flip-flop without effect).
6.2.1.2
Clock divider register
The clock divider register is used to select the CAN mode
of operation (BasicCAN/PeliCAN). Therefore one of the
reserved bits within the PCA82C200 is used. Writing a
value between 0 and 7, as allowed for the PCA82C200,
will enter the BasicCAN mode. The default state is divide
by 12 for Motorola mode and divide by 2 for Intel mode.
An additional function is implemented within anotherof the
reserved bits. Setting of bit CBP (see Table 49) enables
the internal RX input comparator to be bypassed thereby
reducing the internal delays if an external transceiver
circuit is used.
相關PDF資料
PDF描述
SJE1349 NPN PLASTIC POWER TRANSISTOR
SK016R SCRs
SK006V SCRs
SK008D Box-shaped pin header, Discrete wire crimping connection, Discrete wire connectors; HRS No: 543-0505-6 00; No. of Positions: 12; Connector Type: Wire; Contact Gender: Female; Contact Spacing (mm): 2; Terminal Pitch (mm): 2; Current Rating(Amps)(Max.): 2; Operating Temperature Range (degrees C): -30 to 85; General Description: Housing; For Discrete wire; Crimping
SK008L SCRs
相關代理商/技術參數
參數描述
SJA1000/N1,112 功能描述:網絡控制器與處理器 IC STAND-ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
SJA1000/N1112 制造商:NXP Semiconductors 功能描述:IC CAN CONTROLLER 1000 DIP28
SJA1000N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone CAN controller
SJA1000T 制造商:NXP Semiconductors 功能描述:
SJA1000T/N,112 功能描述:網絡控制器與處理器 IC STAND ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*