參數資料
型號： SJA1000
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Stand-alone CAN controller(單機CAN控制器)
中文描述： 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDIP28
封裝： 0.600 INCH, PLASTIC, DIP-28
文件頁數： 12/68頁
文件大?。?/td> 234K
代理商： SJA1000
2000 Jan 04
12
Philips Semiconductors
Product specification
Stand-alone CAN controller
SJA1000
Notes
1.
2.
3.
4.
5.
X means that the value of these registers or bits is not influenced.
Remarks in brackets explain functional meaning.
Reading the command register will always reflect a binary ‘11111111’.
On bus-off the error interrupt is set, if enabled.
Internal read/write pointers of the RXFIFO are reset to their initial values. A subsequent read access to the RXB
would show undefined data values (parts of old messages). If a message is transmitted, this message is written in
parallel to the receive buffer but no receive interrupt is generated and the receive buffer area is not locked. So, even
if the receive buffer is empty, the last transmitted message may be read from the receive buffer until it is overridden
by the next received or transmitted message.
Upon a hardware reset, the RXFIFO pointers are reset to the physical RAM address ‘0’. Setting CR.0 by software or
due to the bus-off event will reset the RXFIFO pointers to the currently valid FIFO start address which is different
from the RAM address ‘0’ after the first release receive buffer command.
6.3.3
C
ONTROL
R
EGISTER
(CR)
The contents of the control register are used to change the behaviour of the CAN controller. Bits may be set or reset by
the attached microcontroller which uses the control register as a read/write memory.
Table 3
Bit interpretation of the control register (CR); CAN address 0
BIT
SYMBOL
NAME
VALUE
FUNCTION
CR.7
CR.6
CR.5
CR.4
OIE
Overrun Interrupt Enable
1
reserved; note 1
reserved; note 2
reserved; note 3
enabled; if the data overrun bit is set, the
microcontroller receives an overrun interrupt
signal (see also status register; Table 5)
disabled; the microcontroller receives no overrun
interrupt signal from the SJA1000
enabled; if the error or bus status change, the
microcontroller receives an error interrupt signal
(see also status register; Table 5)
disabled; the microcontroller receives no error
interrupt signal from the SJA1000
enabled; when a message has been successfully
transmitted or the transmit buffer is accessible
again, (e.g. after an abort transmission command)
the SJA1000 transmits a transmit interrupt signal
to the microcontroller
disabled; the microcontroller receives no transmit
interrupt signal from the SJA1000
0
CR.3
EIE
Error Interrupt Enable
1
0
CR.2
TIE
Transmit Interrupt Enable
1
0
相關PDF資料
PDF描述
SJE1349 NPN PLASTIC POWER TRANSISTOR
SK016R SCRs
SK006V SCRs
SK008D Box-shaped pin header, Discrete wire crimping connection, Discrete wire connectors; HRS No: 543-0505-6 00; No. of Positions: 12; Connector Type: Wire; Contact Gender: Female; Contact Spacing (mm): 2; Terminal Pitch (mm): 2; Current Rating(Amps)(Max.): 2; Operating Temperature Range (degrees C): -30 to 85; General Description: Housing; For Discrete wire; Crimping
SK008L SCRs
相關代理商/技術參數
參數描述
SJA1000/N1,112 功能描述:網絡控制器與處理器 IC STAND-ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
SJA1000/N1112 制造商:NXP Semiconductors 功能描述:IC CAN CONTROLLER 1000 DIP28
SJA1000N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone CAN controller
SJA1000T 制造商:NXP Semiconductors 功能描述:
SJA1000T/N,112 功能描述:網絡控制器與處理器 IC STAND ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*