- 您現在的位置：買賣IC網 > PDF目錄372146 > SJA1000 (NXP SEMICONDUCTORS) Stand-alone CAN controller(單機CAN控制器) PDF資料下載
參數資料
| 型號： | SJA1000 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Stand-alone CAN controller(單機CAN控制器) |
| 中文描述： | 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDIP28 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件頁數： | 13/68頁 |
| 文件大?。?/td> | 234K |
| 代理商： | SJA1000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
2000 Jan 04
13
Philips Semiconductors
Product specification
Stand-alone CAN controller
SJA1000
Notes
1.
2.
Any write access to the control register has to set this bit to logic 0 (reset value is logic 0).
In the PCA82C200 this bit was used to select the synchronization mode. Because this mode is not longer
implemented, setting this bit has no influence on the microcontroller. Due to software compatibility setting this bit is
allowed. This bit will not change after hardware or software reset. In addition the value written by users software is
reflected.
Reading this bit will always reflect a logic 1.
During a hardware reset or when the bus status bit is set to logic 1 (bus-off), the reset request bit is set to logic 1
(present). If this bit is accessed by software, a value change will become visible and takes effect first with the next
positive edge of the internal clock which operates with
1
2
of the external oscillator frequency. During an external reset
the microcontroller cannot set the reset request bit to logic 0 (absent). Therefore, after having set the reset request
bit to logic 0, the microcontroller must check this bit to ensure that the external reset pin is not being held LOW.
Changes of the reset request bit are synchronized with the internal divided clock. Reading the reset request bit
reflects the synchronized status.
After the reset request bit is set to logic 0 the SJA1000 will wait for:
a) One occurrence of bus-free signal (11 recessive bits), if the preceding reset request has been caused by a
hardware reset or a CPU-initiated reset
b) 128 occurrences of bus-free, if the preceding reset request has been caused by a CAN controller initiated bus-off,
before re-entering the bus-on mode; it should be noted that several registers are modified if the reset request bit
was set (see also Table 2).
3.
4.
6.3.4
C
OMMAND
R
EGISTER
(CMR)
A command bit initiates an action within the transfer layer of the SJA1000. The command register appears to the
microcontroller as a write only memory. If a read access is performed to this address the byte ‘11111111’ is returned.
Between two commands at least one internal clock cycle is needed to process. The internal clock is divided by two from
the external oscillator frequency.
CR.1
RIE
Receive Interrupt Enable
1
enabled; when a message has been received
without errors, the SJA1000 transmits a receive
interrupt signal to the microcontroller
disabled; the microcontroller receives no transmit
interrupt signal from the SJA1000
present; detection of a reset request results in
aborting the current transmission/reception of a
message and entering the reset mode
absent; on the ‘1-to-0’ transition of the reset
request bit, the SJA1000 returns to the operating
mode
0
CR.0
RR
Reset Request; note 4
1
0
BIT
SYMBOL
NAME
VALUE
FUNCTION
相關PDF資料 |
PDF描述 |
|---|---|
| SJE1349 | NPN PLASTIC POWER TRANSISTOR |
| SK016R | SCRs |
| SK006V | SCRs |
| SK008D | Box-shaped pin header, Discrete wire crimping connection, Discrete wire connectors; HRS No: 543-0505-6 00; No. of Positions: 12; Connector Type: Wire; Contact Gender: Female; Contact Spacing (mm): 2; Terminal Pitch (mm): 2; Current Rating(Amps)(Max.): 2; Operating Temperature Range (degrees C): -30 to 85; General Description: Housing; For Discrete wire; Crimping |
| SK008L | SCRs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SJA1000/N1,112 | 功能描述:網絡控制器與處理器 IC STAND-ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| SJA1000/N1112 | 制造商:NXP Semiconductors 功能描述:IC CAN CONTROLLER 1000 DIP28 |
| SJA1000N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone CAN controller |
| SJA1000T | 制造商:NXP Semiconductors 功能描述: |
| SJA1000T/N,112 | 功能描述:網絡控制器與處理器 IC STAND ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。