- 您現在的位置：買賣IC網 > PDF目錄372146 > SJA1000 (NXP SEMICONDUCTORS) Stand-alone CAN controller(單機CAN控制器) PDF資料下載
參數資料
| 型號： | SJA1000 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Stand-alone CAN controller(單機CAN控制器) |
| 中文描述： | 2 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PDIP28 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件頁數： | 56/68頁 |
| 文件大?。?/td> | 234K |
| 代理商： | SJA1000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
2000 Jan 04
56
Philips Semiconductors
Product specification
Stand-alone CAN controller
SJA1000
6.5.4.1
CD.2 to CD.0
The bits CD.2 to CD.0 are accessible without restrictions in reset mode as well as in operating mode. These bits are used
to define the frequency at the external CLKOUT pin. For an overview of selectable frequencies see Table 50.
Table 50
CLKOUT frequency selection; note 1
Note
1.
f
osc
is the frequency of the external oscillator (XTAL).
CD.2
CD.1
CD.0
CLKOUT FREQUENCY
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
f
osc
f
2
--------
f
---4
f
--------
f
---8
f
10
--------
f
12
--------
f
14
--------
6.5.4.2
Clock off
Setting this bit allows the external CLKOUT pin of the
SJA1000 to be disabled. A write access is possible only in
reset mode. If this bit is set, CLKOUT is LOW during sleep
mode, otherwise it is HIGH.
6.5.4.3
RXINTEN
This bit allows the TX1 output to be used as a dedicated
receive interrupt output. When a received message has
passed the acceptance filter successfully, a receive
interrupt pulse with the length of one bit time is always
output at the TX1 pin (during the last bit of end of frame).
The transmit output stage should operate in normal output
mode. The polarity and output drive are programmable via
the output control register (see also Section 6.5.3). A write
access is only possible in reset mode.
6.5.4.4
CBP
Setting of CDR.6 allows to bypass the CAN input
comparator and is only possible in reset mode. This is
useful in the event that the SJA1000 is connected to an
external transceiver circuit. The internal delay of the
SJA1000 isreduced,whichwill result in alonger maximum
possible bus length. If CBP is set, only RX0 is active. The
unused RX1 input should be connected to a defined level
(e.g. V
SS
).
6.5.4.5
CAN mode
CDR.7 defines the CAN mode. If CDR.7 is at logic 0 the
CAN controller operates in BasicCAN mode. If set to
logic 1 the CAN controller operates in PeliCAN mode.
Write access is only possible in reset mode.
相關PDF資料 |
PDF描述 |
|---|---|
| SJE1349 | NPN PLASTIC POWER TRANSISTOR |
| SK016R | SCRs |
| SK006V | SCRs |
| SK008D | Box-shaped pin header, Discrete wire crimping connection, Discrete wire connectors; HRS No: 543-0505-6 00; No. of Positions: 12; Connector Type: Wire; Contact Gender: Female; Contact Spacing (mm): 2; Terminal Pitch (mm): 2; Current Rating(Amps)(Max.): 2; Operating Temperature Range (degrees C): -30 to 85; General Description: Housing; For Discrete wire; Crimping |
| SK008L | SCRs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SJA1000/N1,112 | 功能描述:網絡控制器與處理器 IC STAND-ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| SJA1000/N1112 | 制造商:NXP Semiconductors 功能描述:IC CAN CONTROLLER 1000 DIP28 |
| SJA1000N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stand-alone CAN controller |
| SJA1000T | 制造商:NXP Semiconductors 功能描述: |
| SJA1000T/N,112 | 功能描述:網絡控制器與處理器 IC STAND ALONE CAN CONTROLLER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。