- 您現在的位置：買賣IC網 > PDF目錄374663 > S29PL064J (Spansion Inc.) CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control PDF資料下載
參數資料
| 型號： | S29PL064J |
| 廠商： | Spansion Inc. |
| 英文描述： | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| 中文描述： | 3.0伏的CMOS只，同步讀/寫閃存與增強VersatileIO控制記憶 |
| 文件頁數： | 67/106頁 |
| 文件大小： | 1997K |
| 代理商： | S29PL064J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
April 7, 200531107A62
S29PL127J/S29PL129J/S29PL064J/S29PL032J
65
P R E L I M I N A R Y
If DQ5 goes high during a program or erase operation, writing the reset command
returns the banks to the read mode (or erase-suspend-read mode if that bank
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
The autoselect command sequence may be written to an address within a bank
that is either in the read or erase-suspend-read mode. The autoselect command
may not be written while the device is actively programming or erasing in the
other bank.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the bank address and the au-
toselect command. The bank then enters the autoselect mode. The system may
read any number of autoselect codes without reinitiating the command sequence.
Table 21
shows the address and data requirements. To determine sector protec-
tion information, the system must write to the appropriate bank address (BA) and
sector address (SA).
Table 4
shows the address range and bank number associ-
ated with each sector.
The system must write the reset command to return to the read mode (or
erase-suspend-read mode if the bank was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector Command Sequence
The SecSi Sector region provides a secured data area containing a random, eight
word electronic serial number (ESN). The system can access the SecSi Sector re-
gion by issuing the three-cycle Enter SecSi Sector command sequence. The
device continues to access the SecSi Sector region until the system issues the
four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command
sequence returns the device to normal operation. The SecSi Sector is not acces-
sible when the device is executing an Embedded Program or embedded Erase
algorithm.
Table 21
shows the address and data requirements for both command
sequences. See also “SecSi (Secured Silicon) Sector Flash Memory Region” for
further information.
Note that the ACC function and unlock bypass modes are not
available when the SecSi Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the program set-up com-
mand. The program address and data are written next, which in turn initiate the
Embedded Program algorithm. The system is
not
required to provide further con-
trols or timings. The device automatically provides internally generated program
pulses and verifies the programmed cell margin.
Table 21
shows the address and
data requirements for the program command sequence.
Note that the SecSi Sec-
tor, autoselect, and CFI functions are unavailable when a [program/erase]
operation is in progress.
When the Embedded Program algorithm is complete, that bank then returns to
the read mode and addresses are no longer latched. The system can determine
the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to the
"
Write Operation Status" section
section for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm
are ignored.
Note that a
hardware reset
immediately terminates the program
相關PDF資料 |
PDF描述 |
|---|---|
| S29PL127J | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J55 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J60 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J65 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J70 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL064J55BFI120 | 功能描述:閃存 64Mb 3V 55ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29PL064J60BAI120 | 制造商:Spansion 功能描述:FLASH MEM PARALLEL 2.7V TO 3.6V 64M-BIT 4M X 16 60NS 48-PIN - Trays |
| S29PL064J60BFI120 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 60NS 48FBGA - Trays |
| S29PL064J60BFI120(E) | 制造商:Spansion 功能描述:Cut Tape |
| S29PL064J60BFW120 | 制造商:Spansion 功能描述:64M (4MX16) 3V, PAGE MODE, HAZMAT - Trays |
發布緊急采購，3分鐘左右您將得到回復。