參數資料
型號： S29PL064J
廠商： Spansion Inc.
英文描述： CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
中文描述： 3.0伏的CMOS只，同步讀/寫閃存與增強VersatileIO控制記憶
文件頁數： 60/106頁
文件大?。?/td> 1997K
代理商： S29PL064J
58
S29PL127J/S29PL129J/S29PL064J/S29PL032J
31107A62 April 7, 2005
P R E L I M I N A R Y
SecSi Sector Factory-locked Indicator Bit (DQ7) is permanently set to a “1”. Op-
tional Spansion programming services can program the factory-locked area with
a random ESN, a customer-defined code, or any combination of the two. Because
only FASL can program and protect the factory-locked area, this method ensures
the security of the ESN once the product is shipped to the field. Contact your local
sales office for details on using Spansion’s programming services. Note that the
ACC function and unlock bypass modes are not available when the SecSi sector
is enabled.
Customer-Lockable Area (64 words)
The customer-lockable area of the SecSi Sector (000040h-00007Fh) is shipped
unprotected, which allows the customer to program and optionally lock the area
as appropriate for the application. The SecSi Sector Customer-locked Indicator
Bit (DQ6) is shipped as “0” and can be permanently locked to “1” by issuing the
SecSi Protection Bit Program Command. The SecSi Sector can be read any num-
ber of times, but can be programmed and locked only once. Note that the
accelerated programming (ACC) and unlock bypass functions are not available
when programming the SecSi Sector.
The Customer-lockable SecSi Sector area can be protected using one of the
following procedures:
Write the three-cycle Enter SecSi Sector Region command sequence, and
then follow the in-system sector protect algorithm as shown in
Figure 1
, ex-
cept that
RESET# may be at either V
IH
or V
ID
. This allows in-system protec-
tion of the SecSi Sector Region without raising any device pin to a high
voltage. Note that this method is only applicable to the SecSi Sector.
To verify the protect/unprotect status of the SecSi Sector, follow the algo-
rithm shown in
Figure 3
.
Once the SecSi Sector is locked and verified, the system must write the Exit SecSi
Sector Region command sequence to return to reading and writing the remainder
of the array.
The SecSi Sector lock must be used with caution since, once locked, there is no
procedure available for unlocking the SecSi Sector area and none of the bits in
the SecSi Sector memory space can be modified in any way.
SecSi Sector Protection Bits
The SecSi Sector Protection Bits prevent programming of the SecSi Sector mem-
ory area. Once set, the SecSi Sector memory area contents are non-modifiable.
相關PDF資料
PDF描述
S29PL127J CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL127J55 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL127J60 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL127J65 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL127J70 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
相關代理商/技術參數
參數描述
S29PL064J55BFI120 功能描述:閃存 64Mb 3V 55ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL064J60BAI120 制造商:Spansion 功能描述:FLASH MEM PARALLEL 2.7V TO 3.6V 64M-BIT 4M X 16 60NS 48-PIN - Trays
S29PL064J60BFI120 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 60NS 48FBGA - Trays
S29PL064J60BFI120(E) 制造商:Spansion 功能描述:Cut Tape
S29PL064J60BFW120 制造商:Spansion 功能描述:64M (4MX16) 3V, PAGE MODE, HAZMAT - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*