- 您現在的位置：買賣IC網 > PDF目錄374663 > S29PL064J (Spansion Inc.) CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control PDF資料下載
參數資料
| 型號： | S29PL064J |
| 廠商： | Spansion Inc. |
| 英文描述： | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| 中文描述： | 3.0伏的CMOS只，同步讀/寫閃存與增強VersatileIO控制記憶 |
| 文件頁數： | 26/106頁 |
| 文件大?。?/td> | 1997K |
| 代理商： | S29PL064J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
24
S29PL127J/S29PL129J/S29PL064J/S29PL032J
31107A62 April 7, 2005
P R E L I M I N A R Y
I
CC2
in the DC Characteristics table represents the active current specification for
the write mode. See the timing specification tables and timing diagrams in the
"
Reset
" section for write operations.
Accelerated Program Operation
The device offers accelerated program operations through the ACC function. This
function is primarily intended to allow faster manufacturing throughput at the
factory.
If the system asserts V
HH
on this pin, the device automatically enters the afore-
mentioned Unlock Bypass mode, temporarily unprotects any protected sectors,
and uses the higher voltage on the pin to reduce the time required for program
operations. The system would use a two-cycle program command sequence as
required by the Unlock Bypass mode. Removing V
HH
from the WP#/ACC pin re-
turns the device to normal operation.
Note that V
HH
must not be asserted on
WP#/ACC for operations other than accelerated programming, or device damage
may result. In addition, the WP#/ACC pin should be raised to V
CC
when not in
use. That is, the WP#/ACC pin should not be left floating or unconnected; incon-
sistent behavior of the device may result.
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the au-
toselect mode. The system can then read autoselect codes from the internal
register (which is separate from the memory array) on DQ15–DQ0. Standard
read cycle timings apply in this mode. Refer to the "
SecSiTM Sector Addresses
"
section and "
Autoselect Command Sequence
" section for more information.
Standby Mode
When the system is not reading or writing to the device, it can place the device
in the standby mode. In this mode, current consumption is greatly reduced, and
the outputs are placed in the high impedance state, independent of the OE#
input.
The device enters the CMOS standby mode when the CE# (CE1#,CE#2 in
PL129J) and RESET# pins are both held at V
IO
± 0.3 V. (Note that this is a more
restricted voltage range than V
IH
.) If CE# (CE1#,CE#2 in PL129J) and RESET#
are held at V
IH
, but not within V
IO
± 0.3 V, the device will be in the standby mode,
but the standby current will be greater. The device requires standard access time
(t
CE
) for read access when the device is in either of these standby modes, before
it is ready to read data.
If the device is deselected during erasure or programming, the device draws ac-
tive current until the operation is completed.
ICC3 in
“DC Characteristics”
represents the CMOS standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The de-
vice automatically enables this mode when addresses remain stable for t
ACC
+
30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# con-
trol signals. Standard address access timings provide new data when addresses
are changed. While in sleep mode, output data is latched and always available to
the system. Note that during automatic sleep mode, OE# must be at V
IH
before
the device reduces current to the stated sleep mode specification. ICC5 in
“DC
Characteristics”
represents the automatic sleep mode current specification.
相關PDF資料 |
PDF描述 |
|---|---|
| S29PL127J | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J55 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J60 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J65 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
| S29PL127J70 | CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL064J55BFI120 | 功能描述:閃存 64Mb 3V 55ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29PL064J60BAI120 | 制造商:Spansion 功能描述:FLASH MEM PARALLEL 2.7V TO 3.6V 64M-BIT 4M X 16 60NS 48-PIN - Trays |
| S29PL064J60BFI120 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 60NS 48FBGA - Trays |
| S29PL064J60BFI120(E) | 制造商:Spansion 功能描述:Cut Tape |
| S29PL064J60BFW120 | 制造商:Spansion 功能描述:64M (4MX16) 3V, PAGE MODE, HAZMAT - Trays |
發布緊急采購，3分鐘左右您將得到回復。