參數資料
型號： S29PL032J65BFI150
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 65 ns, PBGA56
封裝： 7 X 9 MM, LEAD FREE, FBGA-56
文件頁數： 59/94頁
文件大?。?/td> 949K
代理商： S29PL032J65BFI150
60
S29PL-J
S29PL-J_00_A8 July 29, 2005
Ad van c e
Inf o rmation
Notes:
1. See Table 21 for erase command sequence.
2. See the section on DQ3 for information on the sector erase timer.
Figure 10 Erase Operation
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and
then read data from, or program data to, any sector not selected for erasure. The bank address
is required when writing this command. This command is valid only during the sector erase op-
eration, including the 80 s time-out period during the sector erase command sequence. The
Erase Suspend command is ignored if written during the chip erase operation or Embedded Pro-
gram algorithm.
When the Erase Suspend command is written during the sector erase operation, the device re-
quires a maximum of 35 s to suspend the erase operation. However, when the Erase Suspend
command is written during the sector erase time-out, the device immediately terminates the
time-out period and suspends the erase operation. Addresses are “don’t-cares” when writing the
Erase suspend command.
After the erase operation has been suspended, the bank enters the erase-suspend-read mode.
The system can read data from or program data to any sector not selected for erasure. (The de-
vice “erase suspends” all sectors selected for erasure.) Reading at any address within
erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7,
or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended.
Refer to the Write Operation Status section for information on these status bits.
After an erase-suspended program operation is complete, the bank returns to the erase-sus-
pend-read mode. The system can determine the status of the program operation using the DQ7
or DQ6 status bits, just as in the standard Word Program operation. Refer to the Write Operation
Status section for more information.
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
Data = FFh?
No
Yes
Erasure Completed
Embedded
Erase
algorithm
in progress
相關PDF資料
PDF描述
S29PL127J70BFI000 8M X 16 FLASH 3V PROM, 70 ns, PBGA80
S29XS064R0PBHW010 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44
S2C3R-1-12-H 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS
S2C5R-1-12-RC 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS
S2H3R-1H 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS
相關代理商/技術參數
參數描述
S29PL032J70BAI120 功能描述:閃存 32Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BAI122 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BAW120 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BFI120 功能描述:閃存 32Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BFI120(E) 制造商:Spansion 功能描述:Cut Tape
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*