參數資料
型號: S1C63158D0A010P
元件分類: 微控制器/微處理器
英文描述: 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53
封裝: DIE-53
文件頁數: 109/159頁
文件大?。?/td> 1200K
代理商: S1C63158D0A010P
S1C63808 TECHNICAL MANUAL
EPSON
45
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Clock Timer)
4.7 Clock Timer
4.7.1 Configuration of clock timer
The S1C63808 has a built-in clock timer that uses OSC1 (crystal oscillator) as the source oscillator. The
clock timer is configured of an 8-bit binary counter that serves as the input clock, fOSC1 divided clock
output from the prescaler. Timer data (128–16 Hz and 8–1 Hz) can be read out by the software.
Figure 4.7.1.1 is the block diagram for the clock timer.
128 Hz–16 Hz
Data bus
32 Hz, 8 Hz, 2 Hz, 1 Hz
256 Hz
Clock timer reset signal
Divider
Interrupt
request
Interrupt
control
8 Hz–1 Hz
Clock timer RUN/STOP signal
Clock timer
OSC1
oscillation circuit
(fOSC1)
Fig. 4.7.1.1 Block diagram for the clock timer
Ordinarily, this clock timer is used for all types of timing functions such as clocks.
4.7.2 Data reading and hold function
The 8 bits timer data are allocated to the address FF79H and FF7AH.
<FF79H>
D0: TM0 = 128 Hz
D1: TM1 = 64 Hz
D2: TM2 = 32 Hz
D3: TM3 = 16 Hz
<FF7AH>
D0: TM4 = 8 Hz
D1: TM5 = 4 Hz
D2: TM6 = 2 Hz
D3: TM7 = 1 Hz
Since the clock timer data has been allocated to two addresses, a carry is generated from the low-order
data within the count (TM0–TM3: 128–16 Hz) to the high-order data (TM4–TM7: 8–1 Hz). When this carry
is generated between the reading of the low-order data and the high-order data, a content combining the
two does not become the correct value (the low-order data is read as FFH and the high-order data
becomes the value that is counted up 1 from that point).
The high-order data hold function in the S1C63808 is designed to operate to avoid this. This function
temporarily stops the counting up of the high-order data (by carry from the low-order data) at the point
where the low-order data has been read and consequently the time during which the high-order data is
held is the shorter of the two indicated here following.
1. Period until it reads the high-order data.
2. 0.48–1.5 msec (Varies due to the read timing.)
Note: Since the low-order data is not held when the high-order data has previously been read, the low-
order data should be read first.
相關PDF資料
PDF描述
S1C7XXXF00E199 16-BIT, 90 MHz, RISC MICROCONTROLLER, PQFP
S2041 PHOTO TRANSISTOR DETECTOR
S3P44R10 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
S3S12P128J0VQK 16-BIT, MROM, 1.05 MHz, MICROCONTROLLER, PQFP80
MC9S12P128J0CFTR 16-BIT, FLASH, 1.05 MHz, MICROCONTROLLER, QCC48
相關代理商/技術參數
參數描述
S1C63408 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer