參數資料
型號： QT0086302TME
英文描述： Controller Miscellaneous - Datasheet Reference
中文描述： 控制器雜項-數據表參考
文件頁數： 29/62頁
文件大?。?/td> 268K
代理商： QT0086302TME
82C814
912-3000-047
Revision: 1.0
Page 19
January 08, 1998
OPTi
4.8
Interrupt or SMI service software should perform the following
steps:
Status Change Service Routine
1. Read PCICFG 68h[7, 5:4] to determine whether a dock-
ing station has been recognized.
Test: PCICFG 68h[7] = 0
Yes - Device recognized.
No - Device not recognized. Go to “Retest” section.
Test: PCICFG 68[5:4] = 11
Yes - Docking station recognized.
No - Not a docking station. Exit procedure so that Card-
Bus software can handle event.
2. Read PCICFG 68h[2:1]. The card detection sequencer
drives CVS1 and CVS2 low after detection, so CD1-2#
will stay low.
Test: PCICFG 68h[2:1] = 00
Yes - Docking confirmed.
No - A non zero value indicates that the connection is not
valid or that an undock event has taken place.
3. Read PCICFG 60h to determine the event that caused
the interrupt. Write this same value back to the register to
clear these events, and cause the IRQ line that was
active to go inactive. Also clear PMI event on host chipset
if this was an SMI.
4. Test: Was docking confirmed in step 2
Yes - Go to “Docking Event” section.
No - Force a retest by writing PCICFG 6Dh[6] = 1, and go
to step 1. If this is the second time through, then proceed
to “Undocking Event” section.
4.8.1
1. Read PCICFG 69h to determine the docking station volt-
age.
Docking Event
2. Power up the interface by writing PCICFG 70h[6:4] with
the correct VCC value. PCICFG 70h is typically written to
20h for a 5.0V docking station.
3. Read PCICFG 68h again to check power cycling.
Test: PCICFG 68h[3] = 1
Yes - Continue to next step.
No - There is a problem. Check PCICFG 69h[1] to see if
the VCC value chosen is allowable. If necessary, force a
retest and then start over at step 1.
4. Select PCICLK skew through PCICFG 52h[7:4]. This
value will have to be determined according to the design
of the docking station. Depending on the type of PCICLK
routing used on the docking station, the internal clock
may need to be skewed 1-15ns.
5. Write PCICFG 3Eh[6] = 0 to deassert PCIRST# to the
dock.
The Docking Station devices can now be configured in the
usual manner for PCI devices.
4.8.2
The following step should be followed if an undock event has
been detected.
Undocking Event
1. Test whether PCICFG 69h[0] = 1. If so, data may have
been lost in the undocking event.
On an undock event, no other steps are necessary. The con-
troller automatically powers down the dock, tristates the inter-
face, and asserts the CRST# line.
4.8.3
When undocking, the user can notify the system software
(Windows 95) first so that the system software can turn off
the 82C814 docking side to make a graceful undock. This is
the safest scheme to implement but is not always practical in
a real system because of cost.
Notes on Undocking
If hot undocking is required without notifying the system soft-
ware, shorter CD1-2# pins are required on the docking con-
nector. The CD1-2# pins will change first. The 82C814 will
complete the current cycle on the secondary, and will not
attempt to start another.
The undocking event generates an interrupt to the system, so
that software can check to determine if any posted write data
was left in the FIFO. PCICFG 5Fh returns the number of
retries attempted in flushing the FIFO, which can be used to
determine whether any data was left after the hot undock.
4.8.4
Whenever the result of a test is ambiguous, software should
force the controller to retest the detection pins. Force a retest
by writing PCICFG 6Dh[6] = 1, then start the full service rou-
tine over again. If after several times through this retest
sequence the status cannot be determined, assume an
“undocked” state.
Retest
相關PDF資料
PDF描述
QT110-D IC-QPROX SENSOR
QT110-S IC-SMD-QPROX SENSOR
QT110 SENSOR ICs
QT110H SENSOR ICs
QT113 CHARGE-TRANSFER TOUCH SENSOR
相關代理商/技術參數
參數描述
QT0100 制造商:TE Connectivity 功能描述:Industrial Panel Mount Switches and Lights
QT0102 制造商:TE Connectivity 功能描述:
QT0105 制造商:TE Connectivity 功能描述:Industrial Panel Mount Switches and Lights
QT012 制造商:TE Connectivity 功能描述:
QT01201 功能描述:LIGHT PILOT RELIANT'22RECT BLCK RoHS:是 類別:光電元件 >> 面板指示器，指示燈 系列:Reliant'22 標準包裝:50 系列:- 透鏡顏色:綠 面板切口尺寸:6.4mm（圓形） 電壓:24V 形狀:圓形 類型:LED
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*