- 您現在的位置：買賣IC網 > PDF目錄380549 > MX28F160C3BXAC-90 (MACRONIX INTERNATIONAL CO LTD) 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | MX28F160C3BXAC-90 |
| 廠商： | MACRONIX INTERNATIONAL CO LTD |
| 元件分類： | DRAM |
| 英文描述： | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封裝： | 8 X 6 MM, 1.20 MM HEIGHT, 0.75 MM PITCH, MO-207, CSP-48 |
| 文件頁數： | 31/44頁 |
| 文件大?。?/td> | 429K |
| 代理商： | MX28F160C3BXAC-90 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
31
P/N:PM0867
MX28F160C3T/B
REV. 1.2, MAR. 17, 2004
Figure 8. Automated Sector Erase Flowchart
Bus
Operation
Write
Command
Comments
Erase Setup Data=20H
Addr=Within Sector to Be
Erased
Data=D0H
Addr=Within Sector to Be
Erased
Status Register Data Toggle
CE or OE to Update Status
Register Data
Check SR.7
1=WSM Ready
0=WSM Busy
Write
Erase
Confirm
Read
Standby
Repeat for subsequent sector erasures.
Full status check can be done after each sector erase
or after a sequence of sector erasures.
Write FFH after the last write operation to reset device
to read array mode.
Bus
Operation
Standby
Command
Comments
Check SR.3
1=VPP Low Detect
Check SR.4, 5
Both 1=Command
Sequence Error
Check SR.5
1=Sector Erase Error
Check SR.1
1=Attempted Erase of
Locked Sector- Erase
Aborted
Standby
Standby
Standby
SR.1 and SR.3 MUST be cleared, if set during an erase
attempt, before further attempts are allowed by the
Write State Machine.
SR.1,3,4,5 are only cleared by the Clear Status Reg-
ister Command, in cases where multiple bytes are
erased before full status is checked.
If an error is detected, clear the status register before
attempting retry or other error recovery.
Start
Write 20H
Write D0H and
Sector Address
Full Status Check if Desired
Sector Erase Complete
Read
Status Register
Suspend
Erase Loop
0
No
Yes
1
SR.7=
Suspend Erase
Read Status Register
Data(See Above)
FULL STATUS CHECK PROCEDURE
Sector Erase Successful
SR.3=
0
0
0
0
VPP Range Error
1
Command Sequence Error
1
Sector Erase Error
1
SR.4,5=
SR.5=
Attempted Erase of Locked
Sector - Aborted
1
SR.1=
相關PDF資料 |
PDF描述 |
|---|---|
| MX28F160C3BXAC-90G | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-11 | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-11G | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-70 | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-70G | 16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MX28F160C3BXAC-90G | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-11 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-11G | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| MX28F160C3BXAI-70G | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [1M x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。