- 您現在的位置：買賣IC網 > PDF目錄359235 > MT90826AV (ZARLINK SEMICONDUCTOR INC) Quad Digital Switch PDF資料下載
參數資料
| 型號： | MT90826AV |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 路由/交換 |
| 英文描述： | Quad Digital Switch |
| 中文描述： | TELECOM, DIGITAL TIME SWITCH, PBGA144 |
| 封裝： | 13 X 13 MM, 1.25 MM HEIGHT, MO-192, LBGA-144 |
| 文件頁數： | 29/46頁 |
| 文件大小： | 571K |
| 代理商： | MT90826AV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
MT90826
Data Sheet
29
Zarlink Semiconductor Inc.
6.0 Memory Mapping
The address bus on the microprocessor interface selects the internal registers and memories of the MT90826. If
the A13 address input is low, then the registers are addressed by A12 to A0 according to Table 3.
If the A13 is high, the remaining address input lines are used to select location in the data or connection memory
depending upon MS bit in the control register. For data memory reads, the serial inputs are selected. For
connection memory writes, the serial outputs are selected. The destination stream address bits and channel
address bits are defined by A12 to A8 and A7 to A0 respectively. See Table 4 for the memory address mapping.
The control register controls all the major functions of the device. It selects the internal memory locations that
specify the input and output channels selected for switching and should be programmed immediately after system
power-up to establish the desired switching configuration as explained in the Switching Configurations sections.
The data in the control register consists of the block programming (BPD0-2), the DPLL control (CPLL), the clear
BER test (CBER), the start BER test (SBER), the start frame evaluation (SFE), the block programming enable
(BPE), the memory block programming bit (MBP), the memory select bits (MS), the output stand by bit (OSB) and
the data rate selection (DR0-2) bits. See Table 5 for the description of the control register bits.
7.0 Connection Memory Control
The connection memory controls the switching configuration of the device. Locations of the connection memory are
associated with particular STo output streams.
The TM0 and TM1 bits of each connection memory location allows the selection of Variable throughput delay,
Constant throughput delay, Message or Bit error test mode for all STo channels.
When the variable or constant throughput delay mode is selected, (TM1=0/1, TM0=0), the contents of the stream
address bit (SAB) and the channel address bit (CAB) of the connection memory defines the source information
(stream and channel) of the timeslot that will be switched to the STo streams.
When the message mode is selected, (TM1=0, TM0=1) , only the lower half byte (8 least significant bits) of the
connection memory is transferred to the associated STo output channel.
When the bit error test mode is selected, (TM1=1, TM0=1), the pseudo random pattern will be output on the
associated STo output channel.
See Table 14 for the description of the connection memory bits.
8.0 DTA Data Transfer Acknowledgment Pin
The DTA pin is driven LOW by internal logic, to indicate to the CPU that a data bus transfer is complete. When the
read or write cycle ends, this pin changes to the high-impedance state.
相關PDF資料 |
PDF描述 |
|---|---|
| MT90840AL | Distributed Hyperchannel Switch |
| MT90866AG2 | Flexible 4 K x 2.4 K Channel Digital Switch with H.110 Interface and 2.4 K x 2.4 K Local Switch |
| MT90869 | Flexible 16K Digital Switch (F16kDX) |
| MT90869AG | Flexible 16K Digital Switch (F16kDX) |
| MT90870 | Flexible 12 k Digital Switch (F12kDX) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90840 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Distributed Hyperchannel Switch |
| MT90840AK | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Distributed Hyperchannel Switch |
| MT90840AL | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 512 X 2430/512 X 512/2.373K X 2.373K 5V 100MQFP - Trays |
| MT90840AL1 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 512 X 2430/512 X 512/2.373K X 2.373K 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH DHS 100MQFP 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH DHS 100MQFP |
| MT90840AP | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 512 X 2430/512 X 512/2.373K X 2.373K 5V 84PLCC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。