- 您現在的位置：買賣IC網 > PDF目錄229297 > MT2VDDT832UY-75XX 8M X 32 DDR DRAM MODULE, 0.75 ns, DMA100 PDF資料下載
參數資料
| 型號： | MT2VDDT832UY-75XX |
| 元件分類： | DRAM |
| 英文描述： | 8M X 32 DDR DRAM MODULE, 0.75 ns, DMA100 |
| 封裝： | LEAD FREE, DIMM-100 |
| 文件頁數： | 15/27頁 |
| 文件大?。?/td> | 420K |
| 代理商： | MT2VDDT832UY-75XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
32MB, 64MB (x32, SR)
100-PIN DDR UDIMM
pdf: 09005aef808ebdbc, source: 09005aef808e914b
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD2C8_16x32UG.fm - Rev. D 9/04 EN
22
2004 Micron Technology, Inc. All rights reserved.
SPD Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions (as
shown in Figure 13, Data Validity, and Figure 14, Defi-
nition of Start and Stop).
SPD Start Condition
All commands are preceded by the start condition,
which is a HIGH-to-LOW transition of SDA when SCL
is HIGH. The SPD device continuously monitors the
SDA and SCL lines for the start condition and will not
respond to any command until this condition has been
met.
SPD Stop Condition
All communications are terminated by a stop condi-
tion, which is a LOW-to-HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the SPD device into standby power mode.
SPD Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfers. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data (as shown in Fig-
ure 14, Definition of Start and Stop).
The SPD device will always respond with an
acknowledge after recognition of a start condition and
its slave address. If both the device and a WRITE oper-
ation have been selected, the SPD device will respond
with an acknowledge after the receipt of each subse-
quent eight-bit word. In the read mode the SPD device
will transmit eight bits of data, release the SDA line and
monitor the line for an acknowledge. If an acknowl-
edge is detected and no stop condition is generated by
the master, the slave will continue to transmit data. If
an acknowledge is not detected, the slave will termi-
nate further data transmissions and await the stop
condition to return to standby power mode.
Figure 13: Data Validity
Figure 14: Definition of Start and Stop
Figure 15: Acknowledge Response from Receiver
SCL
SDA
DATA STABLE
DATA
CHANGE
SCL
SDA
START
BIT
STOP
BIT
SCL from Master
Data Output
from Transmitter
Data Output
from Receiver
9
8
Acknowledge
相關PDF資料 |
PDF描述 |
|---|---|
| MB84VD22183EA-85PBS | SPECIALTY MEMORY CIRCUIT, PBGA71 |
| MB84VD22184EA-90PBS | SPECIALTY MEMORY CIRCUIT, PBGA71 |
| M93C66-WMB3TP | 256 X 16 MICROWIRE BUS SERIAL EEPROM, DSO8 |
| MT48LC4M16A2P-75:G | 4M X 16 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| M93C06-MB6G | 16 X 16 MICROWIRE BUS SERIAL EEPROM, DSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT2-X-00-526-3-A21-B-C | 制造商:Carling Technologies 功能描述:M-SERIES CIRCUIT BREAKER - Bulk |
| MT3 | 功能描述:接線端子工具和配件 Markg Tag 5x10mm Horizontal RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
| MT-3 | 功能描述:烙鐵 Weller Chisel Tip For SP23/SP23D RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| MT3/H-1 | 功能描述:接線端子工具和配件 Marking Tag, HorizontalImprint "1" RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
| MT3/H-2 | 功能描述:接線端子工具和配件 Marking Tag, HorizontalImprint "2" RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
發布緊急采購，3分鐘左右您將得到回復。