參數資料
型號: ML53612
廠商: OKI SEMICONDUCTOR CO., LTD.
英文描述: 64-Channel Full Duplex H.100/H.110 CT Bus System Interface and Time-Slot Interchange
中文描述: 64通道全雙工H.100/H.110 CT總線系統接口和時隙交換
文件頁數: 18/68頁
文件大小: 696K
代理商: ML53612
I
ML53612
I
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
14
Oki Semiconductor
5.2 Command/Status Register
Note: For "Reads" that do not require synchronization (all "Reads" except In-Direct Parallel Access Read) it is
not necessary to set this bit. The Data Registers can be read immediately after writing the Address Register.
D_[7:0]
Definition
0
Busy (Read Only)
1
Read Command (Write Only)
2
Write Command (Write Only)
3
Terminate Command (Write Only)
4
Reserved
5
Reserved
6
Reserved
7
Reset (Read/Write)
Busy (D_0) (Read Only)
This bit is set ("1") when a Command that requires synchronization with the ML53612's internal state machine has been initiated, and cleared ("0")
when the command has been completed.
For Commands that do not require synchronization this bit is always clear ("0").
The following commands require synchronization:
Routing Memory Write command
In-Direct Parallel Access Read or Write command
Read (D_1) (Write Only)
Setting this bit ("1") initiates a synchronized read of the register pointed to by the Address Register. When the Busy bit is clear ("0"), the contents of
the register to be read are available by reading the Data Register. It is NOT necessary to clear ("0") this bit after it has been set ("1").
Write (D_2) (Write Only)
Setting this bit ("1") initiates a write of the register pointed to by the Address Register. It is NOT necessary to clear ("0") this bit after it has been set ("1").
Terminate (D_3) (Write Only)
Setting this bit ("1") terminates a command that requires synchronization with the ML53612's internal state machine. The command in process is
completed asynchronously and the Busy bit is cleared. It is NOT necessary to clear ("0") this bit after it has been set ("1").
Reset (D_7) (Read/Write)
Setting this bit ("1") resets the ML53612 and initializes the Configuration and Routing Registers. This command is analogous to the function of the
RESET pin. Clearing this bit ("0") returns the ML53612 to normal operation, ready to be configured.
相關PDF資料
PDF描述
ML60851D USB Device Controller
ML60852 USB Device Controller
ML6190A Longwave Time Code RF Receiver LSI
ML63187 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min).
ML63189B 4-Bit Microcontroller with Built-in 1024-Dot Matrix LCD Drivers and Melody Circuit, Operating at 0.9 V (Min).
相關代理商/技術參數
參數描述
ML536RATR42_LZ 制造商:COILCRAFT 制造商全稱:Coilcraft lnc. 功能描述:High-Reliability Air Core Inductors
ML53812-2 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:H.100/H.110 CT Bus System Interface and Time-Slot Interchange
ML53812-2TC 制造商:ROHM Semiconductor 功能描述:
ML53FAD 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:Micropower CMOS Oscillators
ML53FAG 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:Micropower CMOS Oscillators