參數資料
型號： MC68711E20VFNE2
廠商： Freescale Semiconductor
文件頁數： 65/138頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 52-PLCC
標準包裝： 23
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 38
程序存儲器容量： 20KB（20K x 8）
程序存儲器類型： OTP
EEPROM 大?。?/td> 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 52-LCC（J 形引線）
包裝： 管件
Operating Modes and Memory
MC68HC711D3 Data Sheet, Rev. 2.1
32
Freescale Semiconductor
2.4.2 Programming the EPROM with Downloaded Data
When using this method, the EPROM is programmed by software while in the special test or bootstrap
modes. User-developed software can be uploaded through the SCI or a ROM-resident EPROM
programming utility can be used. The 12-volt nominal programming voltage must be present on the
XIRQ/VPP pin. To use the resident utility, bootload a 3-byte program consisting of a single jump instruction
to $BF00. $BF00 is the starting address of a resident EPROM programming utility. The utility program
sets the X and Y index registers to default values, then receives programming data from an external host,
and puts it in EPROM. The value in IX determines programming delay time. The value in IY is a pointer
to the first address in EPROM to be programmed (default = $F000).
When the utility program is ready to receive programming data, it sends the host the $FF character. Then
it waits. When the host sees the $FF character, the EPROM programming data is sent, starting with the
first location in the EPROM array. After the last byte to be programmed is sent and the corresponding
verification data is returned, the programming operation is terminated by resetting the MCU.
2.4.3 PROM Programming Control Register
The PROM programming control register (PPROG) is used to control the programming of the OTPROM
or EPROM. PPROG is cleared on reset so that the PROM is configured for normal read.
MBE — Multiple Byte Program Enable Bit
This bit is reserved for testing.
Bit 6, 2, and 1 — Not implemented
Always read 0.
ELAT — EPROM (OTPROM) Latch Control Bit
1 = PROM address and data bus are configured for programming. Writes to PROM cause address
and data to be latched. The PROM cannot be read.
0 = PROM address and data bus are configured for normal reads. PROM cannot be programmed.
EXCOL — Select Extra Columns Bit
This bit is reserved for testing.
EXROW — Select Extra Row Bit
This bit is reserved for testing.
PGM — EPROM (OTPROM) Program Command Bit
This bit may be written only when ELAT = 1.
1 = Programming power is switched on to PROM array.
0 = Programming power is switched off.
Address: $003B
Bit 7
654321
Bit 0
Read:
MBE
0
ELAT
EXCOL
EXROW
0
PGM
Write:
Reset:
00000000
Figure 2-5. PROM Programming Control Register (PPROG)
相關PDF資料
PDF描述
MC68882RC50A IC COPROCESSOR FLOAT PT 68-PGA
MC68908GR16CFJE IC MCU 16K FLASH 8MHZ SPI 32LQFP
MC68E360ZQ25VLR2 IC MPU QUICC 32BIT 357-PBGA
MC68EC000EI8R2 IC MPU 32BIT 85MHZ 68-PLCC
MC68EC030FE25CB1 IC MPU 32BIT ENH 25MHZ 132-CQFP
相關代理商/技術參數
參數描述
MC6875 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875A 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875AL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875L 制造商:MOTOROLA 功能描述:IC
MC688 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*