參數資料
型號： MC68711E20VFNE2
廠商： Freescale Semiconductor
文件頁數： 105/138頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 52-PLCC
標準包裝： 23
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 38
程序存儲器容量： 20KB（20K x 8）
程序存儲器類型： OTP
EEPROM 大?。?/td> 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 52-LCC（J 形引線）
包裝： 管件
SCI Error Detection
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
69
6.6 SCI Error Detection
Three error conditions can occur during generation of SCI system interrupts:
Serial communications data register (SCDR) overrun
Received bit noise
Framing
Three bits (OR, NF, and FE) in the serial communications status register (SCSR) indicate if one of these
error conditions exists. The overrun error (OR) bit is set when the next byte is ready to be transferred from
the receive shift register to the SCDR and the SCDR is already full (RDRF bit is set). When an overrun
error occurs, the data that caused the overrun is lost and the data that was already in SCDR is not
disturbed. The OR is cleared when the SCSR is read (with OR set), followed by a read of the SCDR.
The noise flag (NF) bit is set if there is noise on any of the received bits, including the start and stop bits.
The NF bit is not set until the RDRF flag is set. The NF bit is cleared when the SCSR is read (with FE
equal to 1) followed by a read of the SCDR.
When no stop bit is detected in the received data character, the framing error (FE) bit is set. FE is set at
the same time as the RDRF. If the byte received causes both framing and overrun errors, the processor
only recognizes the overrun error. The framing error flag inhibits further transfer of data into the SCDR
until it is cleared. The FE bit is cleared when the SCSR is read (with FE equal to 1) followed by a read of
the SCDR.
6.7 SCI Registers
This subsection describes the five addressable registers in the SCI.
6.7.1 SCI Data Register
The SCI data register (SCDR) is a parallel register that performs two functions. It is the receive data
register when it is read, and the transmit data register when it is written. Reads access the receive data
buffer and writes access the transmit data buffer. Receive and transmit are double buffered.
Address:
$002F
Bit 7
654321
Bit 0
Read:
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
Write:
Reset:
Unaffected by reset
Figure 6-3. SCI Data Register (SCDR)
相關PDF資料
PDF描述
MC68882RC50A IC COPROCESSOR FLOAT PT 68-PGA
MC68908GR16CFJE IC MCU 16K FLASH 8MHZ SPI 32LQFP
MC68E360ZQ25VLR2 IC MPU QUICC 32BIT 357-PBGA
MC68EC000EI8R2 IC MPU 32BIT 85MHZ 68-PLCC
MC68EC030FE25CB1 IC MPU 32BIT ENH 25MHZ 132-CQFP
相關代理商/技術參數
參數描述
MC6875 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875A 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875AL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875L 制造商:MOTOROLA 功能描述:IC
MC688 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*