參數資料
型號： MB8116165B-60
廠商： Fujitsu Limited
英文描述： 1 M ×16 BIT Hyper Page Mode Dynamic RAM(CMOS 1 M ×16位超級頁面存取模式動態RAM)
中文描述： 1米× 16位的超頁模式動態RAM的CMOS（1米× 16位超級頁面存取模式動態內存）
文件頁數： 11/29頁
文件大小： 575K
代理商： MB8116165B-60
11
MB8116165B-50/-60
Notes:
*1.
Referenced to V
SS
.
I
CC
depends on the output load conditions and cycle rates; the specified values are obtained with the
output open.
I
CC
depends on the number of address change as RAS = V
IL
, UCAS = V
IH
, LCAS = V
IH
and V
IL
> –0.3 V.
I
CC1
, I
CC3
, I
CC4
and I
CC5
are specified at one time of address change during RAS = V
IL
and UCAS = V
IH
,
LCAS = V
IH
. I
CC2
is specified during RAS = V
IH
and V
IL
> –0.3 V.
An initial pause (RAS = CAS = V
IH
) of 200
μ
s is required after power-up followed by any eight RAS-
only cycles before proper device operation is achieved. In case of using internal refresh counter, a
minimum of eight CAS-before-RAS initialization cycles instead of 8 RAS cycles are required.
AC characteristics assume t
T
= 2 ns.
V
IH
(min) and V
IL
(max) are reference levels for measuring timing of input signals. Also transition times
are measured between V
IH
(min) and V
IL
(max).
Assumes that t
RCD
≤
t
RCD
(max), t
RAD
≤
t
RAD
(max). If t
RCD
is greater than the maximum recommended
value shown in this table, t
RAC
will be increased by the amount that t
RCD
exceeds the value shown. Refer
to Fig.2 and 3.
If t
RCD
≥
t
RCD
(max), t
RAD
≥
t
RAD
(max), and t
ASC
≥
t
AA
- t
CAC
- t
T
, access time is t
CAC
.
If t
RAD
≥
t
RAD
(max) and t
ASC
≤
t
AA
- t
CAC
- t
T
, access time is t
AA
.
Measured with a load equivalent to two TTL loads and 100 pF.
t
OFF
, t
OFR
, t
WEZ
and t
OEZ
are specified that output buffer change to high-impedance state.
Operation within the t
RCD
(max) limit ensures that t
RAC
(max) can be met. t
RCD
(max) is specified as a
reference point only; if t
RCD
is greater than the specified t
RCD
(max) limit, access time is controlled
exclusively by t
CAC
or t
AA
.
t
RCD
(min) = t
RAH
(min) + 2t
T
+ t
ASC
(min).
Operation within the t
RAD
(max) limit ensures that t
RAC
(max) can be met. t
RAD
(max) is specified as a
reference point only; if t
RAD
is greater than the specified t
RAD
(max) limit, access time is controlled
exclusively by t
CAC
or t
AA
.
Either t
RRH
or t
RCH
must be satisfied for a read cycle.
t
WCS
is specified as a reference point only. If t
WCS
≥
t
WCS
(min) the data output pin will remain High-Z
state through entire cycle.
Assumes that t
WCS
< t
WCS
(min).
Either t
DZC
or t
DZO
must be satisfied.
t
CPA
is access time from the selection of a new column address (that is caused by changing both UCAS
and LCAS from “L” to “H”). Therefore, if t
CP
is long, t
CPA
is longer than t
CPA
(max).
Assumes that CAS-before-RAS refresh.
t
WCS
, t
CWD
, t
RWD
, t
AWD
and
t
CPWD
are not restrictive operating parameters. They are included in the data
sheet as an electrical characteristic only. If t
WCS
≥
t
WCS
(min), the cycle is an early write cycle and D
OUT
pin will maintain high-impedance state throughout the entire cycle. If t
CWD
≥
t
CWD
(min), t
RWD
≥
t
RWD
(min), t
AWD
≥
t
AWD
(min) and t
CPWD
≥
t
CPWD
(min), the cycle is a read-modify-write cycle and data from the
selected cell will appear at the D
OUT
pin. If neither of the above conditions is satisfied, the cycle is a
delayed write cycle and invalid data will appear the D
OUT
pin, and write operation can be executed by
satisfying t
RWL
, t
CWL
, and t
RAL
specifications.
The last CAS rising edge.
The first CAS falling edge.
*2.
*3.
*4.
*5.
*6.
*7.
*8.
*9.
*10.
*11.
*12.
*13.
*14.
*15.
*16.
*17.
*18.
*19.
*20.
*21.
*22.
相關PDF資料
PDF描述
MB8116400A-50 CMOS 4 M ×4 BIT Fast Page Mode DRAM(CMOS 4 M ×4 位快速頁面存取模式動態RAM)
MB8116400A-60 CMOS 4 M ×4 BIT Fast Page Mode DRAM(CMOS 4 M ×4 位快速頁面存取模式動態RAM)
MB8116400A-70 CMOS 4 M ×4 BIT Fast Page Mode DRAM(CMOS 4 M ×4 位快速頁面存取模式動態RAM)
MB8116400B-50 4 M ×4 BITS Fast Page Mode Dynamic RAM(CMOS 4 M ×4 位快速頁面存取模式RAM)
MB8116400B-60 4 M ×4 BITS Fast Page Mode Dynamic RAM(CMOS 4 M ×4 位快速頁面存取模式RAM)
相關代理商/技術參數
參數描述
MB8116E 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:8116E
MB8117800A-60 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2 M X 8 BIT FAST PAGE MODE DYNAMIC RAM
MB8117800A-70 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2 M X 8 BIT FAST PAGE MODE DYNAMIC RAM
MB812 功能描述:ACCY MOUNT BMM 3/4 58A RoHS:是 類別:RF/IF 和 RFID >> RF配件 系列:* 標準包裝:1 系列:*
MB812.833 功能描述:ACCY MOUNT BMM 3/4 58A RoHS:是 類別:RF/IF 和 RFID >> RF配件 系列:* 標準包裝:1 系列:*
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*