- 您現在的位置：買賣IC網 > PDF目錄370961 > M44C090-H (ATMEL CORP) Low-Current Microcontroller for Wireless Communication PDF資料下載
參數資料
| 型號： | M44C090-H |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Low-Current Microcontroller for Wireless Communication |
| 中文描述： | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| 封裝： | SSO-20 |
| 文件頁數： | 11/63頁 |
| 文件大?。?/td> | 503K |
| 代理商： | M44C090-H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
M44C890
M44C090
Rev.A4, 14-Dec-01
11 (63)
Table 3 Interrupt priority table
Interrupt
INT0
INT1
Priority
lowest
|
ROM Address
040h
080h
Interrupt Opcode
C8h (SCALL 040h)
D0h (SCALL 080h)
Function
áááááááááááá
áááááááááááá
áááááááááááá
áááááááááááá
áááááááááááá
áááááááááááá
INT4
INT5
áááááááááááá
áááááááááááá
áááááááááááá
|
|
140h
180h
áááááááááááááááááááá
áááááááááááááááááááá
áááááááááááááááááááá
áááááááááááááááááááá
áááááááááááááááááááá
E8h (SCALL 140h)
F0h (SCALL 180h)
áááááááááááááááááááá
áááááááááááááááááááá
áááááááááááááááááááá
Software interrupt (SWI0)
Timer 2 interrupt
Software interrupt (SW15)
External hardware interrupt, any edge at BP52
áááááááááááááááááááá
áááááááááááá
áááááááááááááááááááá
Table 4 Hardware interrupts
Interrupt
Interrupt Mask
Interrupt Source
Register
P5CR
Bit
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
INT7
INT1
VCM
P53M1, P53M2
VIM
P52M1, P52M2
any edge at BP53
External / internal voltage monitoring
Any edge at BP52
P51M1, P51M2
any edge at BP51
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
Software Interrupts
The programmer can generate interrupts by using the
software interrupt instruction (SWI) which is supported
in qFORTH by predefined macros named SWI0...SWI7.
The software triggered interrupt operates exactly like any
hardware triggered interrupt. The SWI instruction takes
the top two elements from the expression stack and writes
the corresponding bits via the I/O bus to the interrupt
pending register. Therefore, by using the SWI instruction,
interrupts can be re-prioritized or lower priority processes
scheduled for later execution.
Hardware Interrupts
In the M44C090, there are eleven hardware interrupt
sources with seven different levels. Each source can be
masked individually by mask bits in the corresponding
control registers. An overview of the possible hardware
configurations is shown in table 4.
2.3
Master Reset
The master reset forces the CPU into a well-defined
condition. It is unmaskable and is activated independent
of the current program state. It can be triggered by either
initial supply power-up, a short collapse of the power sup-
ply, brown-out detection circuitry, watchdog time-out, or
an external input clock supervisor stage (see figure 9). A
master reset activation will reset the interrupt enable flag,
the interrupt pending register and the interrupt active
register. During the power-on reset phase the I/O bus con-
trol signals are set to
’
reset mode
’
thereby initializing all
on-chip peripherals. All bidirectional ports are set to input
mode. Attention: During any reset phase, the BP20/NTE
input is driven towards V
DD
by a strong pull-up transistor.
Releasing the reset results in a short call instruction
(opcode C1h) to the ROM address 008h. This activates
the initialization routine $RESET which in turn has to
initialize all necessary RAM variables, stack pointers and
peripheral configuration registers (see table 7).
相關PDF資料 |
PDF描述 |
|---|---|
| M44C890 | Low-Current Microcontroller for Wireless Communication |
| M44C890-H | Low-Current Microcontroller for Wireless Communication |
| M4N25 | 6-Pin DIP Optoisolators Transistor Output |
| M4N26 | 6-Pin DIP Optoisolators Transistor Output |
| M4N37 | Header, Vertical Friction Lock; No. of Contacts:3; Pitch Spacing:2.54mm; No. of Rows:1; Gender:Header; Series:6410; Body Material:PA Polyamide (Nylon); Current Rating:4A; Voltage Rating:250V RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M44C890 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Low-Current Microcontroller for Wireless Communication |
| M44C890-H | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Low-Current Microcontroller for Wireless Communication |
| M44S05K4F1 | 功能描述:汽車連接器 MX44 Terminals RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
| M44T332538880MHZ | 制造商:MEC 功能描述: |
| M44T3338880MHZ | 制造商:MEC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。