- 您現在的位置：買賣IC網 > PDF目錄45047 > M38C24M4A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38C24M4A-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 56/102頁 |
| 文件大?。?/td> | 1369K |
| 代理商： | M38C24M4A-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
Rev.2.00
May 28, 2004
page 57 of 100
38C2 Group (A Version)
Fig. 61 Block diagram of built-in flash memory
(1) CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated on
(read, program, or erase) under control of the Central Processing
Unit (CPU).
In CPU rewrite mode, only the User ROM area shown in Figure 61
can be rewritten; the Boot ROM area cannot be rewritten. Make sure
the program and block erase commands are issued for only the User
ROM area and each block area.
The control program for CPU rewrite mode can be stored in either
User ROM or Boot ROM area. In the CPU rewrite mode, because
the flash memory cannot be read from the CPU, the rewrite control
program must be transferred to internal RAM area before it can be
executed.
Boot Mode
The control program for CPU rewrite mode must be written into the
User ROM or Boot ROM area in parallel I/O mode beforehand. (If the
control program is written into the Boot ROM area, the standard se-
rial I/O mode becomes unusable.)
See Figure 61 for details about the Boot ROM area.
Normal microcomputer mode is entered when the microcomputer is
reset with pulling CNVSS pin low. In this case, the CPU starts operat-
ing using the control program in the User ROM area.
When the microcomputer is reset by pulling the P41(CE) pin high,
the CNVSS pin high, the CPU starts operating (start address of pro-
gram is stored into addresses FFFC16 and FFFD16) using the control
program in the Boot ROM area. This mode is called the “Boot mode”.
Also, User ROM area can be rewritten using the control program in
the Boot ROM area.
Block Address
Block addresses refer to the maximum address of each block. These
addresses are used in the block erase command.
100016
800016
FFFF16
F00016
FFFF16
M38C29FFA
100016
100016
800016
FFFF16
F00016
FFFF16
BSEL=0
BSEL=1
User ROM area
4 Kbytes
Boot ROM area
Notes 1: The Boot ROM area can be rewritten in only parallel I/O mode.
(Access to any other areas is inhibited.)
2: To specify a block, use the maximum address in the block.
Parallel I/O mode
CPU rewrite mode, standard serial I/O mode
User area / Boot area select bit = “0”
Block 1 : 28 Kbytes
User ROM area
4 Kbytes
Boot ROM area
Block 1 : 28 Kbytes
Block 0 : 32 Kbytes
User area / Boot area select bit = “1”
Product name
Flash memory
top address
相關PDF資料 |
PDF描述 |
|---|---|
| M38C24M6-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29MC-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M6-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38C24M4-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M4-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-051HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。