- 您現在的位置：買賣IC網 > PDF目錄45047 > M38C24M4A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38C24M4A-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 35/102頁 |
| 文件大?。?/td> | 1369K |
| 代理商： | M38C24M4A-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
Rev.2.00
May 28, 2004
page 38 of 100
38C2 Group (A Version)
Duty
ratio
2
3
4
Voltage value
VL3=VLCD
VL2=2/3 VLCD
VL1=1/3 VLCD
VL3=VLCD
VL2=VL1=1/2 VLCD
Bias Control and Applied Voltage to LCD Power
Input Pins
When the voltage is applied from the LCD power input pins (VL1–
VL3), set the VL pin input selection bit (bit 5 of the LCD power control
register) and VL3 connection bit (bit 6 of LCD power control register)
to “1”, apply the voltage value shown in Table 9 according to the bias
value. In this case, SEG22 pin and SEG23 pin cannot be used.
Select a bias value by the bias control bit (bit 2 of the LCD mode
register).
Fig. 34 Example of circuit at each bias (at external power input)
Table 9 Bias control and applied voltage to VL1–VL3
Bias value
1/3 bias
1/2 bias
Note : VLCD is the maximum value of supplied voltage for the LCD panel.
Table 10 Duty ratio control and common pins used
Note: Unused common pin outputs the unselected waveform.
Common pins used
COM0, COM1
COM0–COM2
COM0–COM3
Bit 1
0
1
Bit 0
1
0
1
Duty ratio selection bits
Common Pin and Duty Ratio Control
The common pins (COM0–COM3) to be used are determined by duty
ratio. Select duty ratio by the duty ratio selection bits (bits 0 and 1 of
the LCD mode register). When reset is released, VCC voltage is out-
put from the common pin.
Segment Signal Output Pin
The segment signal output pins (SEG0–SEG23) are shared with ports
P0–P2. When these pins are used as the segment signal output pins,
set the direction registers of the corresponding pins to “1”, and set
the segment output disable register to “0”.
Also, these pins are set to the input port after reset, the VCC voltage
is output by the pull-up resistor.
VL3
VL2
VL1
R4
R5
R4 = R5
Contrast adjust
1/2 bias
VL3
VL2
VL1
Contrast adjust
R1
R2
R3
R1 = R2 = R3
1/3 bias
相關PDF資料 |
PDF描述 |
|---|---|
| M38C24M6-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29MC-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M6-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38C24M4-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M4-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-051HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。