參數資料
型號： M29DW640F70N6F
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 4M X 16 FLASH 3V PROM, 70 ns, PDSO48
封裝： 12 X 20 MM, LEAD FREE, PLASTIC, TSOP-48
文件頁數： 7/74頁
文件大?。?/td> 556K
代理商： M29DW640F70N6F
M29DW640F
Signal descriptions
2.9
Reset/Block Temporary Unprotect (RP)
The Reset/Block Temporary Unprotect pin can be used to apply a Hardware Reset to the
memory or to temporarily unprotect all Blocks that have been protected.
Note that if VPP/WP is at VIL, then the four outermost boot blocks will remain protected even
if RP is at VID.
A Hardware Reset is achieved by holding Reset/Block Temporary Unprotect Low, VIL, for at
least tPLPX. After Reset/Block Temporary Unprotect goes High, VIH, the memory will be
ready for Bus Read and Bus Write operations after tPHEL or tRHEL, whichever occurs last.
See the Ready/Busy Output section, Table 20 and Figure 16: Reset/Block Temporary
Holding RP at VID will temporarily unprotect the protected Blocks in the memory. Program
and Erase operations on all blocks will be possible. The transition from VIH to VID must be
slower than tPHPHH.
2.10
Ready/Busy Output (RB)
The Ready/Busy pin is an open-drain output that can be used to identify when the device is
performing a Program or Erase operation. During Program or Erase operations Ready/Busy
is Low, VOL. Ready/Busy is high-impedance during Read mode, Auto Select mode and
Erase Suspend mode.
After a Hardware Reset, Bus Read and Bus Write operations cannot begin until Ready/Busy
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
2.11
Byte/Word Organization Select (BYTE)
The Byte/Word Organization Select pin is used to switch between the x8 and x16 Bus
modes of the memory. When Byte/Word Organization Select is Low, VIL, the memory is in
x8 mode, when it is High, VIH, the memory is in x16 mode.
2.12
VCC Supply Voltage
VCC provides the power supply for all operations (Read, Program and Erase).
The Command Interface is disabled when the VCC Supply Voltage is less than the Lockout
voltage, VLKO. This prevents Bus Write operations from accidentally damaging the data
during power up, power down and power surges. If the Program/Erase Controller is
programming or erasing during this time then the operation aborts and the memory contents
being altered will be invalid.
A 0.1F capacitor should be connected between the VCC Supply Voltage pin and the VSS
Ground pin to decouple the current surges from the power supply. The PCB track widths
must be sufficient to carry the currents required during Program and Erase operations, ICC3.
相關PDF資料
PDF描述
M29F002BB120K1 2 Mbit 256Kb x8, Boot Block Single Supply Flash Memory
M29F016D90M6F 2M X 8 FLASH 5V PROM, 90 ns, PDSO44
M29F016D70N1E 2M X 8 FLASH 5V PROM, 70 ns, PDSO40
M29F100B-150M3TR 128K X 8 FLASH 5V PROM, 150 ns, PDSO44
M29F200B-90XM3 256K X 8 FLASH 5V PROM, 90 ns, PDSO44
相關代理商/技術參數
參數描述
M29DW640F70N6T 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
M29DW640F70ZE1 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
M29DW640F70ZE1E 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
M29DW640F70ZE1F 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
M29DW640F70ZE1T 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*