- 您現在的位置：買賣IC網 > PDF目錄369872 > LU3X34FTR (Lineage Power) Quad 3 V 10/100 Ethernet Transceiver(四通道10M位/秒和100 M位/秒以太網收發器) PDF資料下載
參數資料
| 型號： | LU3X34FTR |
| 廠商： | Lineage Power |
| 英文描述： | Quad 3 V 10/100 Ethernet Transceiver(四通道10M位/秒和100 M位/秒以太網收發器) |
| 中文描述： | 四3伏10/100以太網收發器（四通道1000萬位/秒和100海里位/秒以太網收發器） |
| 文件頁數： | 31/52頁 |
| 文件大?。?/td> | 678K |
| 代理商： | LU3X34FTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Lucent Technologies Inc.
31
Preliminary Data Sheet
July 2000
LU3X34FTR
Quad 3 V 10/100 Ethernet Transceiver TX/FX
14
Loopback
1—Enable loopback mode
0—Disable loopback mode
This bit controls the PHY loopback opera-
tion that isolates the network transmitter
outputs (TPTX+/– and FOTX+/–) and
routes the MII transmit data to the MII
receive data path. This function should
only be used when autonegotiation is dis-
abled (bit 12 = 0). The specific PHY
(10Base-T or 100Base-X) used for this
operation is determined by bits 12 and 13
of this register.
1—100 Mbits/s
0—10 Mbits/s
Link speed is selected by this bit or by
autonegotiation if bit 12 of this register is
set (in which case, the value of this bit is
ignored). At powerup or reset, this bit will
be set unless ANEN, FD100, and HD100
pins are all in logic low state.
1—Enable autonegotiation process
0—Disable autonegotiation process
This bit determines whether the link speed
should be set up by the autonegotiation
process. It is set at powerup or reset if the
ANEN pin detects a logic 1 input level.
1—Powerdown
0—Normal operation
Setting this bit puts the LU3X34FTR into
powerdown mode. During the powerdown
mode, TPTX+/– and all LED outputs are
3-stated, FOTX+/– outputs are turned off,
and the MII interface is isolated. RESETZ
is used to clear register.
Note:
Powerdown is an optional function
and is not implemented in this device. Set-
ting this bit does not significantly impact
the power consumption.
1—Isolate PHY from MII
0—Normal operation
Setting this control bit isolates the part
from the MII, with the exception of the
serial management interface. When this
bit is asserted, the LU3X34FTR does not
respond to TXD[3:0], TXEN, and TXER
inputs, and it presents a high impedance
on its TXCLK, RXCLK, RXDV, RXER,
RXD[3:0], COL, and CRS outputs.
R/W
0h
13
Speed Selection
R/W
Pin
12
Autonegotiation Enable
R/W
Pin
11
Powerdown
R/W
0h
10
Isolate
R/W
Pin
Bit(s)
Name
Description
R/W
Default
MII Registers
(continued)
Table 14. Control Register (Register 0h)
(continued)
相關PDF資料 |
PDF描述 |
|---|---|
| LU3X54FT | QUAD-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX |
| LU3X54FTL | QUAD-FET for 10Base-T/100Base-TX/FX |
| LU3X54FTL-HS208-DB | QUAD-FET for 10Base-T/100Base-TX/FX |
| LU3X54FT | Quad-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX(應用于10基數-T和100基數-TX/FX的四快速以太網收發器) |
| LU5X34F | Quad Gigabit Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LU3X34FTR-HS128-DB | 制造商:AGERE 制造商全稱:AGERE 功能描述:Quad 3 V 10/100 Ethernet Transceiver TX/FX |
| LU3X54FT | 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX |
| LU3X54FTL | 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET for 10Base-T/100Base-TX/FX |
| LU3X54FTLHS208 | 制造商:Alcatel-Lucent 功能描述:3X54FTLHS208 |
| LU3X54FTL-HS208-DB | 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET for 10Base-T/100Base-TX/FX |
發布緊急采購，3分鐘左右您將得到回復。