參數資料
型號： ISP1761BE,518
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
封裝： 14 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT425-1, LQFP-128
文件頁數： 152/164頁
文件大?。?/td> 767K
代理商： ISP1761BE,518
ISP1761_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 13 March 2008
87 of 163
NXP Semiconductors
ISP1761
Hi-Speed USB OTG controller
9.4 Host Negotiation Protocol (HNP)
HNP is used to transfer control of the host role between the default host (A-device) and
the default peripheral (B-device) during a session. When the A-device is ready to give up
its role as a host, it will condition the B-device using SetFeature (b_hnp_enable) and will
go into suspend. If the B-device wants to use the bus at that time, it signals a disconnect
to the A-device. Then, the A-device will take the role of a peripheral and the B-device will
take the role of a host.
9.4.1 Sequence of HNP events
The sequence of events for HNP as observed on the USB bus is illustrated in Figure 14.
As can be seen in Figure 14:
1. The A-device completes using the bus and stops all bus activity, that is, suspends the
bus.
2. The B-device detects that the bus is idle for more than 5 ms and begins HNP by
turning off the pull-up on DP. This allows the bus to discharge to the SE0 state.
3. The A-device detects SE0 on the bus and recognizes this as a request from the
B-device to become a host. The A-device responds by turning on its DP pull-up within
3 ms of rst detecting SE0 on the bus.
4. After waiting for 30
s to ensure that the DP line is not HIGH because of the residual
effect of the B-device pull-up, the B-device notices that the DP line is HIGH and the
DM line is LOW, that is, J state. This indicates that the A-device has recognized the
HNP request from the B-device. At this point, the B-device becomes a host and
asserts bus reset to start using the bus. The B-device must assert the bus reset, that
is, SE0, within 1 ms of the time that the A-device turns on its pull-up.
5. When the B-device completes using the bus, it stops all bus activities. Optionally, the
B-device may turn on its DP pull-up at this time.
Remark: The bus idle state will generate a DC suspend interrupt corresponding to the
toggle of the SUSP bit in the DcInterrupt register (address: 218h), when accordingly
enabled.
Fig 14. HNP sequence of events
A-device
1
5
7
2
3
4
6
8
B-device
004aaa079
DP Composite
Legend
DP driven
Pull-up dominates
Pull-down dominates
Normal bus activity
相關PDF資料
PDF描述
ITR8307 SPECIALTY OPTOELECTRONIC DEVICE
IXF1010 10 CHANNEL(S), 1000M bps, LOCAL AREA NETWORK CONTROLLER, CBGA552
JANTX1N3595US-1 0.15 A, SILICON, SIGNAL DIODE
JAN1N3595US-1 0.15 A, SILICON, SIGNAL DIODE
JANTXV1N3595US-1 0.15 A, SILICON, SIGNAL DIODE
相關代理商/技術參數
參數描述
ISP1761BEGE 功能描述:IC USB CTRL HI-SPEED 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1761BE-S 功能描述:IC USB CONTROLLER 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1761BE-T 功能描述:USB 接口集成電路 USB HS OTG CNTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1761BEUM 功能描述:IC USB OTG CONTROLLER HS 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1761ET 功能描述:USB 接口集成電路 USB 2.0 HS OTG HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*