參數資料
型號: EM6517
廠商: Electronic Theatre Controls, Inc.
元件分類: 4位微控制器
英文描述: 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
中文描述: 4位單片機的小型通用紅外遙控器
文件頁數: 9/66頁
文件大?。?/td> 762K
代理商: EM6517
EM6517
FOR ENGINEERING ONLY
EM Microelectronic-Marin SA, 09/99, Rev. A/277
9
The oscillator is disabled during sleep mode. So when waking up from sleep mode, the CPU of the EM6517-1
remains in the reset state for the CPU Reset Delay, to allow the oscillator to stabilize. During this time, the
Oscillation Detection Circuit is inhibited.
In active or standby modes, the oscillator detection circuit monitors the oscillator. If it stops for any reason, a
system reset is generated. After clock restart the CPU waits for the CPU Reset Delay before executing the first
instructions.
The oscillation detection circuitry can be inhibited with bit
NoOscWD
= 1 in register
RegSysCntl3.
At power up,
and after any system reset, the function is activated.
The ‘CPU Reset Delay’ is 32768 system clocks ( Ck[16] ) long.
5.2 Reset Terminal
During active or standby modes the Reset terminal has a debouncer to reject noise. Reset must therefore be
active for at least 16 ms (system clock = 32 KHz).
When canceling sleep mode, the debouncer is not active (no clock), however, reset passes through an
analogue filter with a time constant of typical. 5μs. In this case Reset pin must be high for at least 10 μs to
generate a system reset.
5.3 Input Port A Reset Function
By writing the
OptInpRSel1
and
OptInpRSel2
registers it is possible to choose any combination of port A input
values to execute a system reset. The reset condition must be valid for at least 16ms (system clock = 32kHz) in
active and standby mode.
OPTInpRSleep
selects the input port A reset function in sleep mode. If set to "1" the occurrence of the selected
combination for input port A reset will immediately trigger a system reset (no debouncer) .
Reset combination selection (
InpReset)
is done with registers
OptInpRSel1
and
OptInpRSel2.
Either an ‘AND’ or an ‘OR’ type port A combination can be chosen to generate the reset.
5.3.1 AND-Type Reset function
Default setting(metal option). One or a combination of port A inputs will trigger a reset. Following formula is
applicable :
InpResPA
=
InpResPA[0]
InpResPA[1]
InpResPA[2]
InpResPA[3]
InpRes1PA[n]
0
0
1
1
n = 0 to 3
InpRes2PA[n]
0
1
0
1
InpResPA[n]
V
SS
PA[n]
not PA[n]
V
DD
i.e. ; - no reset if InpResPA[n] = V
SS
.
- Don't care function on a single bit with
its InpResPA[n] = V
DD
.
- Always Reset if InpResPA[3:0] = 'b1111
Figure 9. Input Port A Reset Structure
0
1 MUX
2
3 1 0
V
SS
PA[3]
PA[3]
V
DD
BIT
[0]
BIT
[1]
BIT
[2]
BIT
[3]
InpResPA
InpResPA[3]
InpRes2PA[3]
InpRes1PA[3]
Input Port A Reset
Bit[2] Selection
Input Port A Reset
Bit[1] Selection
Input Port A Reset
Bit[0] Selection
Input Port A Reset
Bit[3] Selection
Input
Reset
from
Port A
相關PDF資料
PDF描述
emg6 General purpose (dual digital transistors)
EMG6 General purpose (dual digital transistors)
EMX-303L1 Magnetic transducer Buzzer
EMX-303L2 Magnetic transducer Buzzer
EMX-303P2 Magnetic transducer Buzzer
相關代理商/技術參數
參數描述
EM6517-240# 制造商:DANAHER - FLUKE 功能描述:BNC TO BANTAM CABLE 制造商:Fluke Electronics 功能描述:BNC TO BANTAM CABLE
EM6520 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:MFP version of EM6620 Ultra Low Power Microcontroller 4x8 LCD Driver
EM6521 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 bit Microcontroller
EM6522 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:This board contains the different MFP’s
EM65240 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Graphic STN LCD Drivers