參數資料
型號： EM6517
廠商： Electronic Theatre Controls, Inc.
元件分類： 4位微控制器
英文描述： 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
中文描述： 4位單片機的小型通用紅外遙控器
文件頁數： 27/66頁
文件大?。?/td> 762K
代理商： EM6517
EM6517
FOR ENGINEERING ONLY
EM Microelectronic-Marin SA, 09/99, Rev. A/277
27
8.6 Counter Setup
RegCDataL[3:0], RegCDataM[3:0], RegCDataH[1:0]
are used to store the initial count value called
CReg[9:0]
which is written into the count register bits
Count[9:0]
when writing the bit
Load
to ‘1’ in
RegCCntl2
.
This bit is automatically reset thereafter.
The counter value
Count[9:0]
can be read
out at any time, except
when using non-debounced high frequency port A input clock. To maintain data integrity the lower nibble
Count[3:0]
must always be read first. The
ShCount[9:4]
values are shadow registers to the counter. To keep
the data integrity during a counter read operation (3 reads), the counter values [9:4] are copied into these
registers with the read of the count[3:0] register. If using non-debounced high frequency port A input the counter
must be stopped while reading the
Count[3:0]
value to maintain the data integrity.
In down count mode an interrupt request
IRQCount0
is generated when the counter reaches 0. In up count
mode, an interrupt request is generated when the counter reaches 3FF (or FF,3F,F if limited bit counting).
Never an interrupt request is generated by loading a value into the counter register.
When the counter is programmed from up into down mode or vice versa, the counter value
Count[9:0]
gets
inverted. As a consequence, the initial value of the counter must be programmed after the
Up/Down
selection.
Loading the counter with hex 000 is equivalent to writing stop mode, the
Start
bit is reset, no interrupt request is
generated.
How to use the counter;
If PWM output is required one has to put the port B[3] in output mode and set PWMOn=1 in step 5.
1st,
set the counter into stop mode (
Start
=0).
2nd,
select the frequency and up-
or
down
count
mode in
RegCCntl1.
3rd,
write the data registers
RegCDataL, RegCDataM, RegCDataH
(counter start value and length)
4th,
load the counter,
Load
=1, and choose the mode. (
EvCount
,
EnComp
=0)
5th,
select bits
PWMOn
in
RegPresc
and
SelIntFull
in
RegSysCntl1
6th,
if compare mode desired , then write
RegCDataL, RegCDataM, RegCDataH
(compare value)
7th,
set bit
Start
and select
EnComp
in
RegCCntl2
8.7 10-bit Counter Registers
Table 8.7.1 Register RegCCntl1
Bit
3
2
CountFSel2
1
CountFSel1
0
CountFsel0
Default : PA0 ,selected as input clock, Down counting
Name
Up/Down
Reset
0
0
0
0
R/W
R/W
R/W
R/W
R/W
Description
Up or down counting
Input clock selection
Input clock selection
Input clock selection
Table 8.7.2 Counter Input Frequency Selection with CountFSel[2..0]
CountFSel2
CountFSel1
0
0
0
0
1
1
1
1
CountFSel0
0
1
0
1
0
1
0
1
clock source selection
Port A PA[0]
Prescaler Ck[15]
Prescaler Ck[12]
Prescaler Ck[10]
Prescaler Ck[8]
Prescaler Ck[4]
Prescaler Ck[1]
Port A PA[3]
0
0
1
1
0
0
1
1
相關PDF資料
PDF描述
emg6 General purpose (dual digital transistors)
EMG6 General purpose (dual digital transistors)
EMX-303L1 Magnetic transducer Buzzer
EMX-303L2 Magnetic transducer Buzzer
EMX-303P2 Magnetic transducer Buzzer
相關代理商/技術參數
參數描述
EM6517-240# 制造商:DANAHER - FLUKE 功能描述:BNC TO BANTAM CABLE 制造商:Fluke Electronics 功能描述:BNC TO BANTAM CABLE
EM6520 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:MFP version of EM6620 Ultra Low Power Microcontroller 4x8 LCD Driver
EM6521 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 bit Microcontroller
EM6522 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:This board contains the different MFP’s
EM65240 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Graphic STN LCD Drivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*