參數資料
型號: EM6517
廠商: Electronic Theatre Controls, Inc.
元件分類: 4位微控制器
英文描述: 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
中文描述: 4位單片機的小型通用紅外遙控器
文件頁數: 25/66頁
文件大?。?/td> 762K
代理商: EM6517
EM6517
FOR ENGINEERING ONLY
EM Microelectronic-Marin SA, 09/99, Rev. A/277
25
8.3 Event Counting
The counter can be used in a special event count mode where a certain number of events (clocks) on the PA[0]
or PA[3] input are counted. In this mode the counting will start directly on the next active clock edge on the
selected port A input.
The Event Count mode is switched on by setting bit
EvCount
in the register
RegCCntl2
to ‘1’.PA[3] and PA[0]
inputs can be inverted depending on register
OPTIntEdgPA
and should be debounced. The debouncer is
switched on in register
OPTDebIntPA
bits NoDebIntPA[3,0]=0. Its frequency depends on the bit
DebSel
from
register
RegPresc
setting. The inversion of the internal clock signal derived from PA[3] or PA[0] is active with
IntEdgPA[3]
respectively
IntEdgPA[0]
equal to 1. Refer also to Figure 12 for internal clock signal generation.
Figure 19. Internal Clock Synchronization
8.4 Compare Function
A previously loaded register value (
CReg[9:0]
) can be compared against the actual counter value (
Count[9:0]
)
.
If the two are matching (equality) then an interrupt (
IRQComp
) is generated. The compare function is switched
on with the bit
EnComp
in the register
RegCCntl2
. With
EnComp
= 0 no
IRQComp
is generated. Starting the
counter with the same value as the compare register is possible, no IRQ is generated on start. Full or Limited
bit compare are possible, defined by bit
SelIntFull
in register
RegSysCntl1
.
EnComp
must be written after a load operation (
Load
= 1). Every load operation resets the bit EnComp.
Full bit compare function.
Bit
SelIntFull
is
set to ‘1’. The function behaves as described above independent of the selected counter length.
Limited bit counting together with full bit compare can be used to generate a certain amount of IRQCount0
interrupts until the counter generates the IRQComp interrupt. With
PWMOn
=‘1’ the counter would have
automatically stopped after the IRQComp, with
PWMOn
=‘0’ it will continue until the software stops it.
EnComp
must be cleared before setting SelIntFull and before starting the counter again. Be careful, PWMOn also
redefines the port B PB[3] output data.(refer to section 8.5).
Limited bit compare
With the bit
SelIntFull
set to ‘0’ (default) the compare function will only take as many bits into account as
defined by the counter length selection
BitSel[1:0]
(see chapter 8.1).
8.5 Pulse Width Modulation (PWM)
The PWM generator uses the behavior of the Compare function (see above) so
EnComp
must be set to
activate the PWM function.. At each Roll Over or Compare Match the PWM state - which is output on port B
PB[3] - will toggle. The start value on PB[3] is forced while
EnComp
is 0 the value is depending on the up or
down count mode. Every counter value load operation resets the bit
EnComp
and therefore the PWM start
value is reinstalled.
Setting
PWMOn
to ‘1’ in register
RegPresc
routes the counter PWM output to port B terminal PB[3]. Insure that
PB[3] is set to output mode . Refer to section 7.4 for the port B setup.
The PWM signal generation is independent of the limited or full bit compare selection bit
SelIntFull.
However if
SelIntFull
= 1 (FULL) and the counter compare function is limited to lower than 10 bits one can generate a
predefined number of output pulses. In this case, the number of output pulses is defined by the value of the
unused counter bits. It will count from the start value until the IRQComp match.
One must not use a compare value of hex 0 in up count mode nor a value of hex 3FF (or FF,3F, F if limited bit
compare) in down count mode.
Ck
Start
Count[9:0
]
+ / - 1
+ / - 1
EvCount = 0
Ck
Start
EvCount = 0
Ck
Start
EvCount = 1
Ck
Start
EvCount = 1
Count[9:0
]
+ / - 1
Count[9:0
]
Count[9:0
]
相關PDF資料
PDF描述
emg6 General purpose (dual digital transistors)
EMG6 General purpose (dual digital transistors)
EMX-303L1 Magnetic transducer Buzzer
EMX-303L2 Magnetic transducer Buzzer
EMX-303P2 Magnetic transducer Buzzer
相關代理商/技術參數
參數描述
EM6517-240# 制造商:DANAHER - FLUKE 功能描述:BNC TO BANTAM CABLE 制造商:Fluke Electronics 功能描述:BNC TO BANTAM CABLE
EM6520 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:MFP version of EM6620 Ultra Low Power Microcontroller 4x8 LCD Driver
EM6521 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4 bit Microcontroller
EM6522 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:This board contains the different MFP’s
EM65240 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Graphic STN LCD Drivers