- 您現在的位置：買賣IC網 > PDF目錄97907 > ELANSC410 Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN PDF資料下載
參數資料
| 型號： | ELANSC410 |
| 英文描述： | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN |
| 中文描述： | ElanSC410 - ElanSC410框圖 |
| 文件頁數： | 81/119頁 |
| 文件大?。?/td> | 1167K |
| 代理商： | ELANSC410 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
64
lanSC310 Microcontroller Data Sheet
PREL IMINARY
System Test and Debug
The lanSC310 microcontroller provides test and
debug features compatible with the standard Test Ac-
cess Port (TAP) and Boundary-Scan Architecture
(JTAG).
The test and debug logic contains the following ele-
ments:
n Five extra pins—TDI, TMS, TCK, TDO, and TRST
(JTAGEN). JTAGEN is dedicated; the other four are
multiplexed.
n Test Access Port (TAP) controller, which decodes
the inputs on the Test Mode Select (TMS) line to
control test operations.
n Instruction Register (IR), which accepts instructions
from the Test Data Input (TDI) pin. The instruction
codes select the specific test or debug operation to
be performed or the test data register to be ac-
cessed.
n Test Data Registers: Boundary Scan Register
(BSR), Device Identification Register (DID), and By-
pass Register (BPR).
Test Access Port (TAP) Controller
The TAP controller is a synchronous, finite state ma-
chine that controls the sequence of operations of the
test logic. The TAP controller changes state in re-
sponse to the rising edge of TCK and defaults to the
test-logic-reset state at power-up. Reinitialization to the
test-logic-reset state is accomplished by holding the
TMS pin High for five TCK periods.
Instruction Register
The Instruction Register is a 4-bit register that allows
instructions to be serially shifted into the device. The in-
struction determines either the test to execute or the
data register to access, or both. The least significant bit
is nearest the TDO output. When the TAP controller en-
ters the capture-IR state, the instruction register is
loaded with the default instruction IDCODE. This is
done to test for faults in the boundary scan connections
at the board level.
Boundary Scan Register
The Boundary Scan Register is a serial shift register
from TDI to TDO, consisting of all the boundary scan
register bits and control cells in each I/O buffer.
Device Identification Register
The Device Identification Register is a 32-bit register
that contains the AMD ID code for the lanSC310 mi-
crocontroller: 195FA003h.
Bypass Register
The Bypass Register provides a path from TDI to TDO
with one clock cycle latency. It helps to bypass a chip
completely while testing boards containing many chips.
Test Access Port Instruction Set
The following instructions are supported:
n Sample/Preload. This instruction enables the sam-
pling of the contents of the boundary scan registers
as well as the serial loading of the boundary scan
registers through TDI.
n Bypass. This instruction connects TDI and TDO
through a 1-bit shift register, the Bypass Register.
n Extest. This instruction enables the parallel loading
of the boundary scan registers. The device inputs
are captured at the input boundary scan cell and the
device outputs are captured at the output boundary
scan cells.
n IDCODE. This instruction connects the ID code reg-
ister between TDI and TDO. The ID code register
contains the fixed ID code value for the device.
JTAG Software
The lanSC310 microcontroller uses combined bidi-
rectional cells. The total number of shifts required to
load the lanSC310 Boundary Scan Register is 173.
The following table shows the relative position of all the
lanSC310 JTAG cells. Note that:
n The chain starts at PMC2 (pin 77) connected to TDI.
n The chain ends at 8042CS (pin 75) connected to
TDO.
n The control cells are located within the chain, their
relative position being indicated in the table.
n The MUXed signals (TCK, TDI, TDO, and TMS) are
not part of the cell chain.
n Control cells are active Low.
n Refer to Figure 10–22 of the IEEE 1149 standard.
相關PDF資料 |
PDF描述 |
|---|---|
| ELH0032G | Fast Operational Amplifier |
| ELH0033G | Fast Buffer Amplifier |
| ELH0101CK | Dual Regulator-Standard Buck PWM and Linear Power Controller; Temperature Range: 0°C to 70°C; Package: 8-SOIC T&R |
| ELH0101ACK | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: -40°C to 85°C; Package: 16-QFN |
| ELH0101 | Power Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC410-100AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC410-100ACAD | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC410-100AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC 3.3V 292-Pin BGA |
| ELANSC410-33AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。