- 您現在的位置：買賣IC網 > PDF目錄97907 > ELANSC410 Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN PDF資料下載
參數資料
| 型號： | ELANSC410 |
| 英文描述： | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN |
| 中文描述： | ElanSC410 - ElanSC410框圖 |
| 文件頁數： | 48/119頁 |
| 文件大小： | 1167K |
| 代理商： | ELANSC410 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
34
lanSC310 Microcontroller Data Sheet
PREL IMINARY
DTR/CFG1
Data Terminal Ready (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to communi-
cate.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
RIN
Ring Indicate (Input; Active Low)
This signal is used as a modem control function. A
change in state on this signal by the external serial de-
vice causes a modem status interrupt. This signal can
be used to cause the lanSC310 microcontroller to re-
sume from a suspended state.
RTS
/CFG0
Request To Send (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to send data.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
SIN
Serial Data In (Input; Active High)
This signal is used to receive the serial data from the
external serial device into the internal serial port
controller.
SOUT
Serial Data Out (Output; Active High)
This signal is used to transmit the serial data from the
internal serial port controller to the external serial
device.
POWER MANAGEMENT INTERFACE
ACIN
AC Input Status (Input; Active High)
When asserted, this signal disables all power manage-
ment functions (if so enabled). It can be used to indi-
cate when the system is being supplied power from an
AC source.
BL4–BL1
Battery Low Detects
(Inputs; Negative Edge Sensitive)
These signals are used to indicate to the lanSC310
microcontroller the current status of the battery. BL4–
BL1 can indicate various conditions of the battery as
status changes. A High indicates normal operating
conditions, while a Low indicates a low voltage warning
condition. These inputs can be used to force the sys-
tem into one of the power saving modes when acti-
vated, as follows:
n BL1 can be programmed to force the system to go
to Low Speed PLL mode or to generate an SMI.
n BL2 can be programmed to force the system to
enter Sleep mode if not already in Sleep mode, or
to generate an SMI.
n BL3 can only be programmed to generate an SMI.
n BL4 can be programmed to force the system to
enter Suspend mode.
EXTSMI
External System Management Interrupt
(Input; Edge Sensitive)
This input is provided to allow external logic to gener-
ate an SMI request to the CPU. It is edge triggered,
with the polarity programmable.
LPH
Latched Power Control (Output; Active Low)
This signal is the inverse of BL4 if ACIN is not true and
BL4 is enabled.
PGP3–PGP0
Programmable Chip Select Generation
(Input/Output)
PGP0 and PGP1 can be programmed as input or out-
put. The default is input. PGP2 and PGP3 are output
only.
These general purpose pins can be individually pro-
grammed as decoder outputs or chip selects for other
external peripheral devices.
PGP0 and PGP2 can be gated with I/O write or act as
an address decode only. PGP1 and PGP3 can be
gated with I/O Read or act as an address decode only.
PGP0 and PGP1 can be directly controlled via a single
register bit if configured to do so. PGP2 and PGP3 can
also be configured for a specific state when the PMU is
in the off state.
PGP2 and PGP3 can be programmed to be set to a
pre-defined state for Micro Power Off mode.
For more information about PGP3–PGP0, see the
lanTMSC310 Microcontroller Programmer’s Refer-
ence Manual, order #20665 and Using 10-Bit ROMCS
Designs in lanTMSC300 and lanSC310 Microcontrol-
lers Application Note, order #21825.
PMC4–PMC0
Power Management Controls
(Output; Programmable)
The Power Management Control outputs control the
power to various external devices and system compo-
nents. The PMC0, PMC1, PMC2, and PMC4 signals
相關PDF資料 |
PDF描述 |
|---|---|
| ELH0032G | Fast Operational Amplifier |
| ELH0033G | Fast Buffer Amplifier |
| ELH0101CK | Dual Regulator-Standard Buck PWM and Linear Power Controller; Temperature Range: 0°C to 70°C; Package: 8-SOIC T&R |
| ELH0101ACK | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: -40°C to 85°C; Package: 16-QFN |
| ELH0101 | Power Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC410-100AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC410-100ACAD | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC410-100AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC 3.3V 292-Pin BGA |
| ELANSC410-33AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。