- 您現在的位置：買賣IC網 > PDF目錄17142 > DEMO9RS08KA2 (Freescale Semiconductor)DEMO BOARD FOR 9RS08KA2 PDF資料下載
參數資料
| 型號： | DEMO9RS08KA2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 88/136頁 |
| 文件大?。?/td> | 0K |
| 描述： | DEMO BOARD FOR 9RS08KA2 |
| 產品培訓模塊： | Mechatronics USBSpyder08 Discovery Kit RS08KA2 Low-End Microcontroller Series MC9RS08KA8 Microcontroller |
| 標準包裝： | 1 |
| 系列： | RS08 |
| 類型： | MCU |
| 適用于相關產品： | MC9RS08KA2 |
| 所含物品： | 板，線纜，CD，文檔，樣品 IC |
| 產品目錄頁面： | 730 (CN2011-ZH PDF) |
| 相關產品： | MC9RS08KA2CSCRTR-ND - IC MCU 8BIT 2K FLASH 8-SOIC PC9RS08KA2PAE-ND - MCU 8BIT 2KB FLASH RS08 8-DIP PC9RS08KA2FPE-ND - MCU 8BIT 2KB FLASH RS08 6-VDFN PC9RS08KA2DWE-ND - MCU 8BIT 2KB FLASH RS08 8-SOIC MC9RS08KA2CPC-ND - IC MCU 8-BIT 2K FLASH 8-PDIP MC9RS08KA2CDB-ND - IC MCU 8-BIT 2K FLASH 6-DFN MC9RS08KA2CSC-ND - IC MCU 8-BIT 2K FLASH 8-SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
Chapter 7 Keyboard Interrupt (RS08KBIV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
55
7.4
Functional Description
This on-chip peripheral module is called a keyboard interrupt (KBI) module because it was originally
designed to simplify the connection and use of row-column matrices of keyboard switches. However, these
inputs are also useful as extra external interrupt inputs and as an external means of waking the MCU from
stop or wait low-power modes.
The KBI module allows its pins to act as additional interrupt sources. Writing to the KBIPEn bits in the
keyboard interrupt pin enable register (KBIPE) independently enables or disables each KBI pin. Each KBI
pin can be configured as edge sensitive or edge and level sensitive based on the KBMOD bit in the
keyboard interrupt status and control register (KBISC). Edge sensitive can be software programmed to be
either falling or rising; the level can be either low or high. The polarity of the edge or edge and level
sensitivity is selected using the KBEDGn bits in the keyboard interrupt edge select register (KBIES).
Synchronous logic is used to detect edges. Prior to detecting an edge, enabled keyboard inputs must be at
the deasserted logic level. A falling edge is detected when an enabled keyboard input signal is seen as a
logic 1 (the deasserted level) during one bus cycle and then a logic 0 (the asserted level) during the next
cycle. A rising edge is detected when the input signal is seen as a logic 0 during one bus cycle and then a
logic 1 during the next cycle.
7.4.1
Edge Only Sensitivity
A valid edge on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt request
will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in KBISC.
7.4.2
Edge and Level Sensitivity
A valid edge or level on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt
request will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in
KBISC, provided all enabled keyboard inputs are at their deasserted levels. KBF will remain set if any
enabled KBI pin is asserted while attempting to clear by writing a 1 to KBACK.
7.4.3
KBI Pullup/Pulldown Device
The KBI pins does not automatically configure an internal pullup/pulldown device when a KBI pin is
enabled. An internal pull device can be used by configuring the associated I/O port pull device enable
register (PTAPE) and pullup/pulldown control register (PTAPUD).
7.4.4
KBI Initialization
When a keyboard interrupt pin is first enabled, it is possible to get a false keyboard interrupt flag. To
prevent a false interrupt request during keyboard initialization, the user should do the following:
1. Mask keyboard interrupts by clearing KBIE in KBISC.
2. If using internal pullup/pulldown device, configure the associated I/O port pullup/pulldown device.
3. Enable the KBI polarity by setting the appropriate KBEDGn bits in KBIES.
4. Enable the KBI pins by setting the appropriate KBIPEn bits in KBIPE.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1B-EZ | CONVERTER MOD DC/DC 95V 25W |
| EBC28DREH | CONN EDGECARD 56POS .100 EYELET |
| ECC35DCMN | CONN EDGECARD 70POS .100 WW |
| EBC35DCSN | CONN EDGECARD 70POS DIP .100 SLD |
| MRJ0280DD-A | C/A MRJ21/MRJ21 GBE STRT CMR 28M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO9RS08KA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR KA8 PRODUCT RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 功能描述:開發板和工具包 - S08 / S12 KB12 DEMO Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE |
| DEMO9RS08LA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR LA8 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08LE4 | 功能描述:開發板和工具包 - S08 / S12 LE4 Family Demo Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
發布緊急采購，3分鐘左右您將得到回復。