- 您現在的位置：買賣IC網 > PDF目錄17142 > DEMO9RS08KA2 (Freescale Semiconductor)DEMO BOARD FOR 9RS08KA2 PDF資料下載
參數資料
| 型號： | DEMO9RS08KA2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 132/136頁 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD FOR 9RS08KA2 |
| 產品培訓模塊： | Mechatronics USBSpyder08 Discovery Kit RS08KA2 Low-End Microcontroller Series MC9RS08KA8 Microcontroller |
| 標準包裝： | 1 |
| 系列： | RS08 |
| 類型： | MCU |
| 適用于相關產品： | MC9RS08KA2 |
| 所含物品： | 板，線纜，CD，文檔，樣品 IC |
| 產品目錄頁面： | 730 (CN2011-ZH PDF) |
| 相關產品： | MC9RS08KA2CSCRTR-ND - IC MCU 8BIT 2K FLASH 8-SOIC PC9RS08KA2PAE-ND - MCU 8BIT 2KB FLASH RS08 8-DIP PC9RS08KA2FPE-ND - MCU 8BIT 2KB FLASH RS08 6-VDFN PC9RS08KA2DWE-ND - MCU 8BIT 2KB FLASH RS08 8-SOIC MC9RS08KA2CPC-ND - IC MCU 8-BIT 2K FLASH 8-PDIP MC9RS08KA2CDB-ND - IC MCU 8-BIT 2K FLASH 6-DFN MC9RS08KA2CSC-ND - IC MCU 8-BIT 2K FLASH 8-SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁當前第132頁第133頁第134頁第135頁第136頁
Modulo Timer (RS08MTIMV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
95
11.4
Functional Description
The MTIM is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector,
and a prescaler block with nine selectable values. The module also contains software selectable interrupt
logic.
The MTIM counter (MTIMCNT) has three modes of operation: stopped, free-running, and modulo. Out
of reset, the counter is stopped. If the counter is started without writing a new value to the modulo register,
then the counter will be in free-running mode. The counter is in modulo mode when a value other than $00
is in the modulo register while the counter is running.
After any MCU reset, the counter is stopped and reset to $00, and the modulus is set to $00. The bus clock
is selected as the default clock source and the prescale value is divide by 1. To start the MTIM in
free-running mode, simply write to the MTIM status and control register (MTIMSC) and clear the MTIM
stop bit (TSTP).
Four clock sources are software selectable: the internal bus clock, the fixed frequency clock (XCLK), and
an external clock on the TCLK pin, selectable as incrementing on either rising or falling edges. The MTIM
clock select bits (CLKS) in MTIMCLK are used to select the desired clock source. If the counter is active
(TSTP = 0) when a new clock source is selected, the counter will continue counting from the previous
value using the new clock source.
Nine prescale values are software selectable: clock source divided by 1, 2, 4, 8, 16, 32, 64, 128, or 256.
The prescaler select bits (PS) in MTIMCLK select the desired prescale value. If the counter is active
(TSTP = 0) when a new prescaler value is selected, the counter will continue counting from the previous
value using the new prescaler value.
The MTIM modulo register (MTIMMOD) allows the overflow compare value to be set to any value from
$01 to $FF. Reset clears the modulo value to $00, which results in a free running counter.
When the counter is active (TSTP = 0), the counter increments at the selected rate until the count matches
the modulo value. When these values match, the counter overflows to $00 and continues counting. The
MTIM overflow flag (TOF) is set whenever the counter overflows. The flag sets on the transition from the
modulo value to $00. Writing to MTIMMOD while the counter is active resets the counter to $00 and
clears TOF.
Clearing TOF is a two-step process. The first step is to read the MTIMSC register while TOF is set. The
second step is to write a 0 to TOF. If another overflow occurs between the first and second steps, the
clearing process is reset and TOF will remain set after the second step is performed. This will prevent the
second occurrence from being missed. TOF is also cleared when a 1 is written to TRST or when any value
is written to the MTIMMOD register.
The MTIM allows for an optional interrupt to be generated whenever TOF is set. To enable the MTIM
overflow interrupt, set the MTIM overflow interrupt enable bit (TOIE) in MTIMSC. TOIE must never be
written to a 1 while TOF = 1. Instead, TOF must be cleared first, then the TOIE can be set to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1B-EZ | CONVERTER MOD DC/DC 95V 25W |
| EBC28DREH | CONN EDGECARD 56POS .100 EYELET |
| ECC35DCMN | CONN EDGECARD 70POS .100 WW |
| EBC35DCSN | CONN EDGECARD 70POS DIP .100 SLD |
| MRJ0280DD-A | C/A MRJ21/MRJ21 GBE STRT CMR 28M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO9RS08KA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR KA8 PRODUCT RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 功能描述:開發板和工具包 - S08 / S12 KB12 DEMO Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE |
| DEMO9RS08LA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR LA8 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08LE4 | 功能描述:開發板和工具包 - S08 / S12 LE4 Family Demo Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
發布緊急采購，3分鐘左右您將得到回復。