參數資料
型號： CY7C1381D-133BZXC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： DRAM
英文描述： 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
中文描述： 512K X 36 CACHE SRAM, 6.5 ns, PBGA165
封裝： 13 X 15 MM, 1.40 MM HEIGHT, LEAD FREE, MO-216, FBGA-165
文件頁數： 7/29頁
文件大?。?/td> 477K
代理商： CY7C1381D-133BZXC
PRELIMINARY
CY7C1381D
CY7C1383D
Document #: 38-05544 Rev. *A
Page 7 of 29
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. Maximum access delay from
the clock rise (t
CDV
) is 6.5 ns (133-MHz device).
The CY7C1381D/CY7C1383D supports secondary cache in
systems utilizing either a linear or interleaved burst sequence.
The interleaved burst order supports Pentium
and i486
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is
user-selectable, and is determined by sampling the MODE
input. Accesses can be initiated with either the Processor
Address Strobe (ADSP) or the Controller Address Strobe
(ADSC). Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
Byte write operations are qualified with the Byte Write Enable
(BW
E
) and Byte Write Select (BWX) inputs. A Global Write
Enable (GW) overrides all byte write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self-timed write circuitry.
Three synchronous Chip Selects (CE
1
, CE
2
, CE
3[2]
) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE
1
is HIGH.
Single Read Accesses
A single read access is initiated when the following conditions
are satisfied at clock rise: (1) CE
1
, CE
2
, and CE
3[2]
are all
asserted active, and (2) ADSP or ADSC is asserted LOW (if
the access is initiated by ADSC, the write inputs must be
deasserted during this first cycle). The address presented to
the address inputs is latched into the address register and the
burst counter/control logic and presented to the memory core.
If the OE input is asserted LOW, the requested data will be
available at the data outputs a maximum to tCDV after clock
rise. ADSP is ignored if CE
1
is HIGH.
Single Write Accesses Initiated by ADSP
This access is initiated when the following conditions are
satisfied at clock rise: (1) CE
1
, CE
2
, CE
3[2]
are all asserted
active, and (2) ADSP is asserted LOW. The addresses
presented are loaded into the address register and the burst
inputs (GW, BW
E
, and BW
X
)are ignored during this first clock
cycle. If the write inputs are asserted active ( see Write Cycle
Descriptions table for appropriate states that indicate a write)
on the next clock rise,the appropriate data will be latched and
written into the device.Byte writes are allowed. All I/Os are
tri-stated during a byte write.Since this is a common I/O
device, the asynchronous OE input signal must be deasserted
and the I/Os must be tri-stated prior to the presentation of data
to DQs. As a safety precaution, the data lines are tri-stated
once a write cycle is detected, regardless of the state of OE.
Single Write Accesses Initiated by ADSC
This write access is initiated when the following conditions are
satisfied at clock rise: (1) CE
1
, CE
2
, and CE
3[2]
are all asserted
active, (2) ADSC is asserted LOW, (3) ADSP is deasserted
HIGH, and (4) the write input signals (GW, BWE, and BW
X
)
indicate a write access. ADSC is ignored if ADSP is active LOW.
The addresses presented are loaded into the address register
and the burst counter/control logic and delivered to the
memory core. The information presented to DQ
[A:D]
will be
written into the specified address location. Byte writes are
allowed. All I/Os are tri-stated when a write is detected, even
a byte write. Since this is a common I/O device, the
asynchronous OE input signal must be deasserted and the
I/Os must be tri-stated prior to the presentation of data to DQs.
As a safety precaution, the data lines are tri-stated once a write
cycle is detected, regardless of the state of OE.
Burst Sequences
The CY7C1381D/CY7C1383D provides an on-chip two-bit
wraparound burst counter inside the SRAM. The burst counter
is fed by A
[1:0]
, and can follow either a linear or interleaved
burst order. The burst order is determined by the state of the
MODE input. A LOW on MODE will select a linear burst
sequence. A HIGH on MODE will select an interleaved burst
V
SSQ
TDO
I/O Ground
JTAG serial output
Synchronous
Ground for the I/O circuitry
.
Serial data-out to the JTAG circuit
. Delivers data on the negative edge of TCK. If the
JTAG feature is not being utilized, this pin should be left unconnected. This pin is not
available on TQFP packages.
Serial data-In to the JTAG circuit
. Sampled on the rising edge of TCK. If the JTAG feature
is not being utilized, this pin can be left floating or connected to V
DD
through a pull up
resistor. This pin is not available on TQFP packages.
Serial data-In to the JTAG circuit
. Sampled on the rising edge of TCK. If the JTAG feature
is not being utilized, this pin can be disconnected or connected to V
DD
. This pin is not
available on TQFP packages.
Clock input to the JTAG circuitry
. If the JTAG feature is not being utilized, this pin must
be connected to V
SS
. This pin is not available on TQFP packages.
No Connects
. Not internally connected to the die. 36M, 72M, 144M and 288M are address
expansion pins are not internally connected to the die.
This pin can be connected to Ground or should be left floating.
TDI
JTAG serial input
Synchronous
TMS
JTAG serial input
Synchronous
TCK
JTAG-
Clock
–
NC
V
SS
/DNU
Ground/DNU
Pin Definitions
(continued)
Name
I/O
Description
相關PDF資料
PDF描述
CY7C1383D 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
CY7C1383D-100AXC 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
CY7C1383D-100AXI 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
CY7C1383D-100BGC 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
CY7C1383D-100BGI 18-Mbit (512K x 36/1M x 18) Flow-Through SRAM
相關代理商/技術參數
參數描述
CY7C1381DV25-133AXC 制造商:Cypress Semiconductor 功能描述:
CY7C1381F-133BGC 功能描述:靜態隨機存取存儲器 512Kx36 3.3V Sync FT 靜態隨機存取存儲器 RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
CY7C1381F-133BGCT 功能描述:靜態隨機存取存儲器 512Kx36 3.3V Sync FT 靜態隨機存取存儲器 RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
CY7C1381S-133AXC 功能描述:靜態隨機存取存儲器 CY7C1381S-133AXC RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
CY7C1381XC 制造商:Cypress Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*