參數資料
型號： CC113LRTKT
廠商： TEXAS INSTRUMENTS INC
元件分類： 無繩電話/電話
英文描述： TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PQCC20
封裝： 4 X 4 MM, GREEN, PLASTIC, VQFN-20
文件頁數： 39/75頁
文件大?。?/td> 1454K
代理商： CC113LRTKT
CC113L
SWRS108A
Page 44 of 68
25.2
Calibration in Multi-Channel Systems
CC115L is highly suited for multi-channel
systems due to its agile frequency synthesizer
and effective communication interface.
Charge pump current, VCO current, and VCO
capacitance array calibration data is required
for each frequency when implementing a multi-
channel system. There are 3 ways of obtaining
the calibration data from the chip:
1) Calibration for every frequency change. The
PLL calibration time is 712/724 s (26 MHz
crystal and TEST0 = 0x09/0B, see Table 27).
The blanking interval between each frequency
is then 787/799 s.
2) Perform all necessary calibration at startup
and store the resulting FSCAL3, FSCAL2, and
FSCAL1 register values in MCU memory. The
VCO capacitance calibration FSCAL1 register
value must be found for each RF frequency to
be used. The VCO current calibration value
and the charge pump current calibration value
available in FSCAL2 and FSCAL3 respectively
are not dependent on the RF frequency, so the
same value can therefore be used for all RF
frequencies for these two registers. Between
each
frequency
change,
the
calibration
process can then be replaced by writing the
FSCAL3, FSCAL2 and FSCAL1 register values
that corresponds to the next RF frequency.
The PLL turn on time is approximately 75 s
(Table 26). The blanking interval between
each frequency hop is then approximately
75 s.
3) Run calibration on a single frequency at
startup. Next write 0 to FSCAL3[5:4] to
disable the charge pump calibration. After
writing to FSCAL3[5:4], strobe SRX with
for
each
new
frequency. That is, VCO current and VCO
capacitance calibration is done, but not charge
pump current calibration. When charge pump
current calibration is disabled the calibration
time is reduced from 712/724 s to 145/157 s
(26 MHz crystal and TEST0 = 0x09/0B, see
Table 27). The blanking interval between each
frequency hop is then 220/232 s.
There is a trade-off between blanking time and
memory space needed for storing calibration
data in non-volatile memory. Solution 2) above
gives
the
shortest
blanking
interval,
but
requires
more
memory
space
to
store
calibration values. This solution also requires
that the supply voltage and temperature do not
vary much in order to have a robust solution.
Solution 3) gives 567 s smaller blanking
interval than solution 1).
The
recommended
settings
for
change
with
frequency. This means that one should always
use SmartRF Studio [4] to get the correct
settings for a specific frequency before doing a
calibration, regardless of which calibration
method is being used.
Note: The content in the TEST0 register is
not retained in SLEEP state, thus it is
necessary to re-write this register when
returning from the SLEEP state.
相關PDF資料
PDF描述
CC154Z-A6BP45-FREQTSB-OUT27 VCXO, CLOCK, 8 MHz - 36 MHz, HCMOS OUTPUT
CC1812C513R-10 CHOKE CAN-BUS 51.0UH 200MA
CC2824B475R-10 CHOKE CAN-BUS 4700.0UH 400MA
CC2824D225R-10 CHOKE CAN-BUS 2200.0UH 500MA
CC2824E105R-10 CHOKE CAN-BUS 1000.0UH 700MA
相關代理商/技術參數
參數描述
CC113U015R3C3PH 制造商:Mallory 功能描述:CGA015X311B
CC1140M3M 制造商:SHIELD 制造商全稱:SHIELD s.r.l. 功能描述:For electrovalves, style A, 3p+G, female, with cable
CC1140M8M 制造商:SHIELD 制造商全稱:SHIELD s.r.l. 功能描述:For electrovalves, style A, 3p+G, female, with cable
CC-115 制造商:B&K Precision Corporation 功能描述:
CC1150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CC1100 Single Chip Low Cost Low Power RF-Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*