參數資料
型號: ARM60
廠商: Mitel Networks Corporation
英文描述: Low Power General Purpose 32-Bit RISC Microprocessor(低功耗通用32位精簡指令集微處理器)
中文描述: 低功耗通用32位RISC微處理器(低功耗通用32位精簡指令集微處理器)
文件頁數: 19/121頁
文件大小: 1217K
代理商: ARM60
Programmer's Model
15
software which must work out the cause of the
aborted instruction. The application program needs no knowledge of the amount of memory available to
it, nor is its state in any way affected by the abort.
abort, make the requested data available, and retry the
3.4.4 Software interrupt
The software interrupt instruction (SWI) is used for getting into Supervisor mode, usually to request a
particular supervisor function. When a SWI is executed, ARM60 performs the following:
(1)
Saves the address of the SWI instruction plus 4 in R14_svc; saves CPSR in SPSR_svc
(2)
Forces M[4:0]=10011 (Supervisor mode) and sets the I bit in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x08
To return from a SWI, use MOVS PC,R14_svc. This will restore the PC and CPSR and return to the
instruction following the SWI.
3.4.5 UndeTned instruction trap
When the ARM60 comes across an instruction which it cannot handle (see
offers it to any coprocessors which may be present. If a coprocessor can perform this instruction but is busy
at that time, ARM60 will wait until the coprocessor is ready or until an interrupt occurs. If no coprocessor
can handle the instruction then ARM60 will take the undefined instruction trap.
Chapter 4.0 Instruction Set
), it
The trap may be used for software emulation of a coprocessor in a system which does not have the
coprocessor hardware, or for general purpose instruction set extension by software emulation.
When ARM60 takes the undefined instruction trap it performs the following:
(1)
Saves the address of the Undefined or coprocessor instruction plus 4 in R14_und; saves CPSR in
SPSR_und.
(2)
Forces M[4:0]=11011 (Undefined mode) and sets the I bit in the CPSR
(3)
Forces the PC to fetch the next instruction from address 0x04
To return from this trap after emulating the failed instruction, use MOVS PC,R14_und. This will restore the
CPSR and return to the instruction following the undefined instruction.
相關PDF資料
PDF描述
ARM610 General Purpose 32-Bit Microprocessor with 4kByte Cache,Write Buffer and Memory Management Unit(通用32位微處理器(帶4K字節緩存,寫緩沖器和存儲器管理單元))
ARRAYS NIGHT VISION H.V. RECTIFIER DIODES & ARRAYS
ARS2540 40A GLASS PASSIVATED AVALANCHE BUTTON DIODE
AR2540 40A GLASS PASSIVATED AVALANCHE BUTTON DIODE
ARS25A 25A AUTOMOTIVE BUTTON DIODE
相關代理商/技術參數
參數描述
ARM607 制造商:Master Appliance Corp 功能描述:Armature, With Retaining Rings, 120V (HG 制造商:Master Appliance Corp 功能描述:Armature, With Retaining Rings, 120V (HG-751B)
ARM-607 制造商:Master Appliance Corp 功能描述:Nozzle Shield; HG-751B heat gun 制造商:Master Appliance 功能描述:Heat Gun,Armature W/Retaining Ring For Hg-751B 120V, Hg-501A-D
ARM610 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:General purpose 32-bit microprocessor
ARM7-009 制造商:Gravitech 功能描述:ARM7 LPC2378 W/2.8" TCH SCRN LCD BLU
ARM720T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:General-purpose 32-bit Microprocessor with 8KB cache, enlarged Write buffer, and Memory Management Unit (MMU) combined in a single chip