- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-53050 Frequency Agile Transceiver PDF資料下載
參數資料
| 型號： | AMIS-53050 |
| 英文描述： | Frequency Agile Transceiver |
| 中文描述： | 捷變頻收發器 |
| 文件頁數： | 78/107頁 |
| 文件大?。?/td> | 2576K |
| 代理商： | AMIS-53050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁
AMIS-53050
Frequency Agile Transceiver
Data Sheet
6.10.1.7. RF PLL Trim
This register contains the value of the trim from the self calibration. The values written to this register by the PLL calibration can provide
some indication of the quality of the frequency selection. Values at the maximum or minimum allowed for the TX or RX trim function,
even when calibration passes, may indicate (although not necessarily) that a different value for the VCO external LC components could
provide better performance or that a slightly different frequency should be used.
Table 74: RF PLL Trim - 0X27 [39]
Bit
Name
State
Comment
7
Max. VCO trim value from the self calibration
Min. VCO trim value from the self calibration
3
Max. VCO trim value from the self calibration
Min. VCO trim value from the self calibration
6:4
TX Mode PLL
trim value
111
--000
2:0
RX Mode PLL
trim value
111
--
000
6.10.1.8. PLL Target Value
This register is used by the AMIS-53050 during sel
register with no user-defined function.
.10.2. Calibrate Quick Start Oscillator
6
he Quick Start oscillator must be calibrated prior to operations such as sniff or burst transmit. This command will perform an internal
calibration of the oscillator, write the result to the Quick Start trim register, issue a calibration complete flag, as well as a calibration
good/bad indicator. This command can be issued from any valid state that accepts changes in the instructions.
6.10.3. Calibrate 10kHz Oscillator
and then perform the calibration and store the result. A cal done and status flag will be issued upon completion of the
ed from any valid state that accepts changes in the instructions.
n. This command can be issu
alibratio
c
10.4.
6.
rms a calibration for the PLL in both transmit and receive mode. The PLL status register reports the calibration
alibrate the PLL perfo
both modes, as well as the status for the calibration. This command can be issued from any valid state that accepts
structions. This calibration is required when the AMIS-53050 is first powered on or returned from a device reset
in
tr
or receive instruction is issued).
alue for
the in
ansmit
changes
(before a
.10.5. Cali
6
This com
maximum
AMIS-53
tolerance of exter
N
the AMIS-53050 receiver.
in
oth the LNA output tuning structure and the LNA input matching trim for
on typically performed at board assembly in the presence of a known RF signal. The
050 will auto-tune both the input and output internal variable capacitances of the LNA to optim
nal omponents for the match.
ize gain, compensating for the
ote:
O
put to
level should be high enough to be above the noise)
f calibration. This is an internal use
T
In any of the idle modes of operation, an internal 10kHz oscillator is used as the timekeeping reference for the interval timers. The
calibrate 10kHz oscillator command will enable the crystal oscillator to create an accurate time base to use for the calibration of this
scillator,
o
Calibrate PLL
C
v
brate LNA
mand turns on the RF receiver chain and optimizes b
signal level on RSSI. This is a calibrati
nly perform this calibration with a known, non-modulated, signal input (the
78
AMI Semiconductor
– Jan. 07, M-20639-002
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-710650 | Color CIS Module Analog Video Output |
| AMIS-710650-A6 | Color CIS Module Analog Video Output |
| AMIS-710651 | Color CIS Module |
| AMIS-710651-A4 | Color CIS Module |
| AMIS-720233 | Contact Image Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-53050-I/A | 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver |
| AMIS-53050-XTD | 功能描述:射頻收發器 AMIS-53050 WLESS TRNSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| AMIS-70020 | 制造商:ON Semiconductor 功能描述:POWER FAILURE ELAPSED TIME COUNTER, SOIC - Rail/Tube 制造商:ON Semiconductor 功能描述:POWER FAILURE ELAPSED TIME COUNTER, SOIC - Tape and Reel |
| AMIS-710200 | 制造商:AMI 制造商全稱:AMI 功能描述:200dpi CIS Module |
| AMIS-710201 | 制造商:AMI 制造商全稱:AMI 功能描述:200dpi CIS Module |
發布緊急采購，3分鐘左右您將得到回復。