參數資料
型號： AMIS-30622
英文描述： I2C Microstepping Motordriver
中文描述： 的I2C微步Motordriver
文件頁數： 14/35頁
文件大?。?/td> 2887K
代理商： AMIS-30622
AMI Semiconductor - Rev. 2.3
www.amis.com
14
9.2.1.3 External Switch and HW Pin
Pin SWI and hardwired address pin HW (see § 9.2.4.3
Physical Address) will alternatively attempt to source and
sink a current in/from the external switch (see application
schematic) to test whether it is ON or OFF. This current is
set around 10mA when a 1k
external series resistor is
used.
This can be represented by the following time diagram (the
timings are given in § 6).
If the switch is detected ON (closed), then the flag
<ESW>
is
raised. The status of this flag can be read by the application
via a
GetActualPos
or a
GetFullStatus1
reading
frame. At the falling edge of every current pulse (at around
1kHz), the stepper motor actual position is refreshed
(register ActPos, see § 9.2.2.9), so that the master node
may get synchronous information about the state of the
switch together with the position of the motor. The position
is then given with an accuracy of ± 1 half-step (or micro-
step, depending of the programmed stepping mode). The
block diagram below shows how this function is
implemented for HW.
With the following truth table:
State
Float
Float
Float
Float
HWLo
HWLo
HWLo
HWLo
HWHi
HWHi
HWHi
HWHi
Sink
1
1
0
0
1
1
0
0
1
1
0
0
Source
0
0
1
1
0
0
1
1
0
0
1
1
New State
Float
HWHi
Float
HWLo
HWLo
HWHi
Float
HWLo
Float
HWHi
HWHi
HWLo
HWHi
HWLo
address = "1"
address = "0"
Note
If HW is detected to be floating, motion to the secure position is performed.
note that e.g. if HW is connected
to GND, LS-part will report "float"
while HS-part will report "low
resistance detected".
AMIS-30622 I
2
C Microstepping Motordriver
Data Sheet
相關PDF資料
PDF描述
AMIS-30660 High Speed CAN Transceiver
AMIS-39100 Octal High Side Driver with Protection
AMIS39100AGA Octal High Side Driver with Protection
AMIS-39101 Octal High-Side Driver with Protection
AMIS39101AGA Octal High-Side Driver with Protection
相關代理商/技術參數
參數描述
AMIS-30622AGA 制造商:ON Semiconductor 功能描述:MICROSTEPPING MOTOR CNTRLR - Rail/Tube 制造商:ON Semiconductor 功能描述:MICROSTEPPING MOTOR CNTRLR - Tape and Reel
AMIS-30622ANA 制造商:ON Semiconductor 功能描述:MICROSTEPPING MOTOR CNTRLR - Trays 制造商:ON Semiconductor 功能描述:MICROSTEPPING MOTOR CNTRLR - Tape and Reel
AMIS30622C6223G 功能描述:馬達/運動/點火控制器和驅動器 I2C STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMIS30622C6223RG 功能描述:馬達/運動/點火控制器和驅動器 I2C STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMIS30622C6227G 功能描述:馬達/運動/點火控制器和驅動器 I2C 800mA MICRO STP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*