參數資料
型號： ADUC7036DCPZ
廠商： Analog Devices Inc
文件頁數： 42/132頁
文件大小： 0K
描述： IC MCU 96K FLASH DUAL 48LFCSP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 115°C
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
包裝： 托盤
ADuC7036
Rev. C | Page 17 of 132
Pin No.
Mnemonic
Type1
Description
11
NTRST
I
JTAG Test Reset. This reset input pin is one of the standard 5-pin JTAG debug ports on the part.
NTRST is an input pin only and has an internal, weak pull-down resistor. This pin remains
unconnected when not in use. NTRST is also monitored by the on-chip kernel to enable LIN
boot load mode.
12
TMS
I
JTAG Test Mode Select. This mode select input pin is one of the standard 5-pin JTAG debug ports
on the part. TMS is an input pin only and has an internal, weak pull-up resistor. This pin is left
unconnected when not in use.
13
VBAT
I
Battery Voltage Input to Resistor Divider.
14
VREF
I
External Reference Input Terminal. When this input is not used, connect it directly to the AGND
system ground. It can also be left unconnected.
15
GND_SW
I
Switch to Internal Analog Ground Reference. This pin is the negative input for the external
temperature channel and external reference. When this input is not used, connect it directly to
the AGND system ground.
18
VTEMP
I
External Pin for NTC/PTC Temperature Measurement.
19
IIN+
I
Positive Differential Input for Current Channel.
20
IIN
I
Negative Differential Input for Current Channel.
21, 22
AGND
S
Ground Reference for On-Chip Precision Analog Circuits.
24
REG_AVDD
S
Nominal 2.6 V Output from On-Chip Regulator.
27
GPIO_0/IRQ0/SS
I/O
General-Purpose Digital I/O 0/External Interrupt Request 0/Slave Select Input for SPI Interface.
By default and after power-on reset, this pin is configured as an input. The pin has an internal,
weak pull-up resistor and should be left unconnected when not in use.
28
GPIO_1/SCLK
I/O
General-Purpose Digital I/O 1/Serial Clock Input for SPI Interface. By default and after a power-
on reset, this pin is configured as an input. The pin has an internal, weak pull-up resistor and
should be left unconnected when not in use.
29
GPIO_2/MISO
I/O
General-Purpose Digital I/O 2/Master Input, Slave Output for SPI Interface. By default and after a
power-on reset, this pin is configured as an input. The pin has an internal, weak pull-up resistor
and should be left unconnected when not in use.
30
GPIO_3/MOSI
I/O
General-Purpose Digital I/O 3/Master Output, Slave Input for SPI Interface. By default and after a
power-on reset, this pin is configured as an input. The pin has an internal, weak pull-up resistor
and should be left unconnected when not in use.
31
GPIO_4/ECLK
I/O
General-Purpose Digital I/O 4/2.56 MHz Clock Output. By default and after a power-on reset, this
pin is configured as an input. The pin has an internal, weak pull-up resistor and should be left
unconnected when not in use.
33
REG_DVDD
S
Nominal 2.6 V Output from the On-Chip Regulator.
36
XTAL1
O
Crystal Oscillator Output. If an external crystal is not used, this pin is left unconnected.
37
XTAL2
I
Crystal Oscillator Input. If an external crystal is not used, connect this pin to the DGND system
ground.
41
WU
I/O
High Voltage Wake-Up Pin. This high voltage I/O pin has an internal, 10 kΩ pull-down resistor
and a high-side driver to VDD. If this pin is not being used, it should not be connected externally.
42
VDD
S
Battery Power Supply to On-Chip Regulator.
44
VSS
S
Ground Reference. This is the ground reference for the internal voltage regulators.
46
STI
I/O
High Voltage Serial Test Interface Output Pin. If this pin is not used, externally connect it to the
IO_VSS ground reference.
47
IO_VSS
S
Ground Reference for High Voltage I/O Pins.
48
LIN/BSD
I/O
Local Interconnect Network I/O/Bit Serial Device I/O. This is a high voltage pin.
EPAD
Exposed pad
The exposed pad should be connected to DGND.
1 I = input, O = output, I/O = input/output, S = supply.
相關PDF資料
PDF描述
MC74HC4051ADTR2G IC MUX/DEMUX 8X1 16TSSOP
ADUC7036BCPZ IC MCU FLASH 96K ANLGI/O 48LFCSP
ATSAM3X4EA-AU IC MCU 2X128KB CORTEX-M3 144-QFP
AT91SAM7X128C-AU IC MCU 32BIT 128KB FLASH 100LQFP
NC7WB66L8X IC SWITCH DUAL SPST-NO 8MICROPAK
相關代理商/技術參數
參數描述
ADUC7036DCPZ-RL 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7038WBCPZ-RL 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 制造商:Analog Devices 功能描述:ARM Microcontrollers - MCU Flash 64k ARM7 Dual 16-Bit ADC LIN IC 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7039 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated, Precision Battery Sensor for Automotive Systems
ADUC7039BCP6Z 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC7039BCP6Z-RL 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*