- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC7032BSTZ-8V-RL (Analog Devices Inc)IC BATTERY SENSOR PREC 48-LQFP PDF資料下載
參數資料
| 型號： | ADUC7032BSTZ-8V-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 91/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BATTERY SENSOR PREC 48-LQFP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI，UART/USART |
| 外圍設備： | POR，PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 9 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 105°C |
| 封裝/外殼： | 48-LQFP |
| 包裝： | 標準包裝 |
| 其它名稱： | ADUC7032BSTZ-8V-RLDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁當前第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Preliminary Technical Data
ADuC7032
Rev. PrD | Page 65 of 128
A factory or end-of-line calibration for the I-ADC would be a
2-step procedure:
1. Apply 0A current.
Configure the ADC in the required PGA setting etc. and write
to ADCMDE[2:0] to perform a System Zero-Scale Calibration.
This writes a new offset calibration value into ADC0OF.
2. Apply a Full-Scale current for the selected PGA setting.
Write to ADCMDE to perform a System Full-Scale Calibration.
This writes a new gain calibration value into ADC0GN.
Understanding the Offset and Gain Calibration
Registers
The output of the average block in the ADC signal flow
described earlier after the digital filter and before the Offset and
Gain scaling can be considered to be a fractional number with a
span, for a +/- Full-Scale input, of approx +/-0.75. The span is
less than +/-1.0 because there is attenuation in the modulator
to accommodate some over-range capacity on the input signal.
The exact value of the attenuation will vary slightly from part-
to-part, because of manufacturing tolerances.
The Offset Coefficient is read from the ADC0OF calibration
register. This value is a 16-Bit 2's complement number. The
range of this number, in terms of the signal chain, is effectively
+/-1.0. 1 LSB of the ADC0OF register is therefore not the same
as 1LSB of ADC0DAT.
A positive value of ADC0OF indicates that offset is subtracted
from the output of the filter, a negative value is added. The
nominal value of this register is 0x0000, indicating zero offset is
to be removed. The actual offset of the ADC may vary slightly
from part-to-part and at different PGA gains. The offset within
the ADC is minimized if the Chopping mode is active
(ADCFLT[15]=1).
The Gain Coefficient is a unitless scaling factor. The 16-Bit
value in this register is divided by 16384, and then multiplied
by the offset-corrected value. The nominal value of this register
equals 0x5555, which corresponds to a multiplication factor of
1.3333. This scales the nominal +/-0.75 signal to produce a full-
scale output signal of +/-1.0 which is checked for Overflow/
Underflow and converted to Two's Complement or Unipolar
mode as appropriate, before being output to the Data register.
The actual gain, and the required scaling coefficient for zero
gain error, varies slightly from part to part, and at different
PGA settings and in Normal / Low-Power-Mode. The value
downloaded into ADC0GN at power-on/reset represents the
scaling factor for a PGA Gain=1. There will be some level of
gain error if this value is used at different PGA settings. User
code can over-write the calibration coefficients or run ADC
calibrations to correct the gain error at the current PGA setting.
In Summary, the simplified ADC transfer function can be
described as :
ADCGNNOM
ADCGN
ADCOF
VREF
VIN
ADCOUT
*
=
This equation is valid for Voltage/Temperature channel ADC.
For the Current Channel ADC,
ADCGNNOM
ADCGN
ADCOF
K
VREF
VIN
ADCOUT
*
=
where K is dependent on PGA gain setting and ADC mode.
Normal Mode:
For PGA gains of 1,4,8,16,32 and 64 the K factor is 1. For
PGA gains of 2 and 128 the K factor is 2. For PGA gain of 256
the K Factor is 4. For PGA gain of 512, the K factor is 8.
Low Power Mode:
The PGA gain is set to 128 and the K factor is 32.
Low Power Plus Mode:
The K factor is 8.
In Low-Power and Low-Power-Plus Mode, the K factor doubles
if (AVDD_Reg)/2 is used as the reference.
ADC DIAGNOSTICS
The ADuC7032 features diagnostic capability on all three
ADCs.
Current ADC Diagnostics
The ADuC7032 features the capability to detect Open Circuit
conditions on the application board. This is accomplished
using the two current sources on IIN+ and IIN-, which is
controlled via ADC0CON[14,13].
The use of both the IIN+ and IIN- current sources is shown in
Table 33.
To verify the current ADC is converting correctly, it is possible
to select an internal test voltage via ADC0CON[7,6]. Selecting
mode 10 results in the current ADC converting the Voltage
Reference, e.g. The Precision 1.2V Reference, divided by 136 for
PGA settings less than or equal to 128 and divided by
(1.0625*Gain) for PGA settings greater than 128.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7034BCPZ | IC MCU FLASH 32K ANLG IO 48LFCSP |
| ADUC7036CCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| ADUC7039BCP6Z-RL | IC MCU ARM7 BATT SENSER 32LFCSP |
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7033 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
| ADUC7033BCPZ-8L | 制造商:Analog Devices 功能描述:Integrated Precision Battery Sensor 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Trays |
| ADUC7033BCPZ-8L-RL | 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LFCSP EP - Tape and Reel |
| ADUC7033BSTZ-88 | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ADUC7033BSTZ-88-RL | 功能描述:IC BATT SENSOR PREC 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。